1. Provide a block diagram and a function table for the NOR-Gate Latch. 2. Describe, with the aid of a circuit diagram, the operation of a 6-bit parallel-to-serial converter. Assume the parallel input is "111010". Draw the timing diagram which covers at least 7 clock cycles. 3. Describe, with the aid of a circuit diagram, the operation of a BCD (Binary Coded Decimal) counter. A single document (MS Word or PDF) containing: • The block diagram and function table required in Q1 The descriptions, circuit diagram and timing diagram required in Q2 The descriptions and circuit diagram required in Q3

1. Provide a block diagram and a function table for the NOR-Gate Latch. 2. Describe, with the aid of a circuit diagram, the operation of a 6-bit parallel-to-serial converter. Assume the parallel input is "111010". Draw the timing diagram which covers at least 7 clock cycles. 3. Describe, with the aid of a circuit diagram, the operation of a BCD (Binary Coded Decimal) counter. A single document (MS Word or PDF) containing: • The block diagram and function table required in Q1 The descriptions, circuit diagram and timing diagram required in Q2 The descriptions and circuit diagram required in Q3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Explain and Define the following logic gates. OR AND NAND NOT
answer the ff. tnxxxxxxx
A NOR gate has an input voltage Vcc equal to 5V. The input current is 2.2mA for high output and 3.5mA for low output. Find the power dissipated for 50% duty cycle.
Q4: Suggest a control gate drive circuit for a Triac, which is used to control a fan regulator. The gate signals should be synchronized with the input voltage. Draw the complete: 1. Circuit diagram with the load and 2. The waveform of the input and output voltages. ) Q.13 Indicate whether the following statements are correct or not then correct the incorrect statements 1) the multi pulse selected notching technique used in inverter is used to eliminate the low order harmonics and to reduce switching frequency, 2) In 3-phase half-controlled half-wave rectifier, the firing angle can be varied from 0 to 180 degrees while in 6-phase half-controlled half-wave rectifier can be varied from 0 to 150 degrees Q.14 Indicate whether the following statements are correct or not then correct the incorrect statements 1) In rectifier circuits, lower pulse number and connecting either primary or secondary of 3- phase winding in delta will reduce the harmonics content of the drawr. current 2) In…
1. Explain the A/D & D/A converter with necessary diagram. 2. Draw various pulse generating ckts with 555 timer IC. 3. Design a CMOS circuit with the equation- Y=A'C+B+D’
Draw a clock signal CLK with five 0-to-1 timing events, a nonzero setup time, tsu, and a nonzero hold time,th. Also draw one excitation input signal EI that follows the sequence 10110 and meets the setup and hold timerequirements. In the excitation input, the first bit in the sequence (1) occurs in time for the first clock timingevent, the second bit in the sequence (0) occurs in time for the second clock timing event, and so forth.
Q1. Using a Finite State Machine, Design a counter that: Count: 000, 010, 111, 011, 110, 100, 001, 101, 000, 010, 111, .. the Reset: Asynchronous active-low input signal. It initializes the count to "000". The input E: Synchronous input that increases the count when it is set to '1'. The output z: It becomes '1' when the count is 101. Provide the State Diagram in any representation. reset E. clock Counter
3. (a) The data sheet of a quad two-input AND gate (type 74S08) specifies the propagation delay and power supply parameters as Vcc = 5.0 V (typical), IcCH (for all four gates) = 18 mA, ICCL (for all four gates) = 32 mA, tpLH= 4.5 ns and tpHL = 5.0 ns. Determine the speed- power product specification. (b) Represent the following in the IEEE-754 floating-point standard using the single- precision format. (i) 32-bit binary number 11110000 11001100 10101010 00001111; (ii) (–118.625)10
Q1. Design asynchronous (ripple ) binary counter and timing diagram for the following sequence (0,1,2,3,4,5) Q2. Determine the resolution expressed as a percentage of 16-bit DAC.