Question1: a) Describe the importance of the following relationship: ΔΤ NG S ΘΕ b) If a VLSI chip in a package has AT 90°C, o 2.0°C/W, and E-0.2pJ find out what is the maximum number of gates on this chip when all gates are operating simultaneously with each gate having switching speed (propagation delay) of Insec. c) Determine how much power can be dissipated.

Question1: a) Describe the importance of the following relationship: ΔΤ NG S ΘΕ b) If a VLSI chip in a package has AT 90°C, o 2.0°C/W, and E-0.2pJ find out what is the maximum number of gates on this chip when all gates are operating simultaneously with each gate having switching speed (propagation delay) of Insec. c) Determine how much power can be dissipated.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If the gate bias is disabled, the channel of a J-FET is ____. a.short circuited b.open circuited c.All of the above d.unaffected e.destroyed
Q2) Derive the NOT gate and then sketch the MUX equivalen?
Draw the circuit diagram of 4-bit Ripple Carry Adder. Page 6 of 8
19. With necessary diagrams and equations, describe the operation of different types of single-phase PWM inverters. Compare multiple-pulse and sinusoidal pulse modulation schemes with single-phase PWM scheme.
What is the midpoint voltage in volts for a CMOS 4-input NAND gate with W/Lp = 78.7 and W/Ln 68.6 ? Assume simultaneous switching, and use: VDD = 3.3V VTN = 0.7V VTP = -0.7V, k'n = 100uA/V^2, k'p = 40uA/V^2 Answer The correct answer is 2.09
Assume Vth = 1V and k = 50mA/V2. Given the schematic below, do the following: 1) Indicate and verify the state of each MOSFET and ?0 for the following input combinations. Fill-out the table below for each assumed state of the MOSFET for every input combination. Use ?ds,on approximation for linear operation. 2) Determine what kind of logic circuit is implemented in the circuit.
Write VHDL code for a modulo-13 counter (counting sequence is 010, 110, …. 1210). The counter has the following features: a synchronous Active High Reset a value R can be loaded into the counter, using the signal Ld (Load) The signal Ld is active High Draw the schematic of your counter, showing the inputs and outputs. Show the number of bits for R, Q (output of the counter), Ld.
**Without Explain Please ****Without Explain Please ****Without Explain Please ** 1. When a press switch is connected to VDD one side and the other to the mid of two resistor as voltage divider which one end to the ground and the other goes to P3 is called.. a.Not activeb.Active highc.Active low 2. In the AVR ATMEGA16 the structure of the IO/p ports includes … a.1 ADCb.8 ADCc.2ADCd.4 ADC 3. The sketch for AVR ATMEGA16 when connected to an LED PORTD |=(0x01<<0) means a.Turn on PC1b.Turn off PC0 1c.Turn on PC0 d.Turn off PC1 4. The sketch for AVR ATMEGA16 statement if((PINC &(0x01<<2))==1) means a.Wait for PINC1 to be logic 1 b.Wait for PINC1 to be logic 0 c.Wait for PINC2 to be logic 0. d.Wait for PINC2 to be logic 1 5. The sketch for AVR ATMEGA16 statement PORTB &=~(0x00<<1)means a.Turn on PB1b.Turn off PB0c.Turn off PB1 d.Turn on PB 0 **Without Explain Please **
7) The following figure shows a transistor-level (CMOS) circuit for some logic gate. Sketch the logic gate for the CMOS gate. Choices: a) NAND gate b) AND gate c) OR gate d) NOR gate
How many states the PN sequence generator of DB20 have? • What is the length of PN sequence generator of DB20? • Calculate the outputs of each clock and put them on the Table (2). • What is the PN Sequence of the DB20. • Verify the outputs you get with the outputs from the device.
Q2) A) Based on the count sequence and decoding operations of 74LS90S ICs shown in Figure below. Q2) B) Use the SAR ADC to convert the analog voltage of (7.28 V) to 8-bit binary. If (VREF = 10V), determine the final %3D binary answer and the percent error. 01011101, 0.1974588% 11011101, 0.1974588% 01011111, 0.1974588% 01111101, 0.1974588%
• Discussion: • How many states the PN sequence generator of DB20 have? • What is the length of PN sequence generator of DB20? • Calculate the outputs of each clock and put them on the Table (2). • What is the PN Sequence of the DB20. • Verify the outputs you get with the outputs from the device.