Problem:1 The following is the system data for a load flow solution. Determine the bus voltages at the end of first iteration using Gauss-Seidel method : Take a = 1.6. The line admittances: Bus code Admittance 1-2 2-j8.0 1-3 1-j4.0 23 0.666-j2.664 24 1-j4.0 34 2-j8.0 The schedule of active and reactive powers: Bus code P V Remarks 1.06 Slack 0.2 1+ j0.0 1+ j0.0 1+ j0.0 2 0.5 PQ 0.4 0.3 PQ 0.3 0.1 PQ

Problem:1 The following is the system data for a load flow solution. Determine the bus voltages at the end of first iteration using Gauss-Seidel method : Take a = 1.6. The line admittances: Bus code Admittance 1-2 2-j8.0 1-3 1-j4.0 23 0.666-j2.664 24 1-j4.0 34 2-j8.0 The schedule of active and reactive powers: Bus code P V Remarks 1.06 Slack 0.2 1+ j0.0 1+ j0.0 1+ j0.0 2 0.5 PQ 0.4 0.3 PQ 0.3 0.1 PQ

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.32P

See similar textbooks

Similar questions

Equipment ratings for the five-bus power system shown in Figure 7.15 are as follows: Generator G1:Â Â Â Â 50Â MVA,Â 12kV,Â X=0.2 per unit Generator G2: 100Â MVA, 15 kV, X=0.2 per unit Transformer T1: 50 MVA, 10 kV Y/138kVY,X=0.10 per unit Transformer T2: 100 MVA, 15 kV /138kVY,X=0.10 per unit Each 138-kV line: X1=40 A three-phase short circuit occurs at bus 5, where the prefault voltage is 15 kV. Prefault load current is neglected. (a) Draw the positive-sequence reactance diagram in unit on a 100-MVA, 15-kV base in the zone of generator G2. Determine (b) the ThĂ©venin equivalent at the fault, (c) the subtransient fault current in per unit and in kA rms, and (d) contributions to the fault from generator G2 and from transformer T2.
In a 7-bus system, the double line fault is occurred at bus -5. During fault the positive sequence potential difference between the bus-4 and bus-1is found to be 0.0175. what is the line impedance which is connected between bus-4 and bus-1 if the current flowing through transmission line is -j 0.148? Select one: O a. -jo.182 O b. +j0.1182 O c. -jo.1182 O d. +j0.182
Q2. Figure Q2 shows the single-line diagram. The scheduled loads at buses 2 and 3 are as marked on the diagram. Line impedances are marked in per unit on 100 MVA base and the line charging susceptances are neglected. a) Using Gauss-Seidel Method, determine the phasor values of the voltage at load bus 2 and 3 according to second iteration results. b) Find slack bus real and reactive power according to second iteration results. c) Determine line flows and line losses according to second iteration results. d) Construct a power flow according to second iteration results. Slack Bus = 1.04.20° 0.025+j0.045 0.015+j0.035 0.012+j0,03 3 |2 134.8 MW 251.9 MW 42.5 MVAR 108.6 MVAR
A DC Optimal Power Flow problem is to be solved for a 3-bus network. The per-unit reactances of the lines interconnecting the buses are as follows: X12 = 0.1pu, X13 = 0.12 pu and X23 = 0.2 pu. There is a generator at each bus. The loads at buses 1, 2 and 3 are 150MW, 200mw, and 100MWrespectively. Bus 1 is taken as the reference bus, and SBase = 100 MVA. Which one of the below is a constraint of the DCOPF problem? Select one: O a. None of these O b. -500 0₂-1000 03 = P3 - 110 O c. 1500 0₂-500 03 = P₂ - 220 O d. 1500 0₂-500 03 = P₂ - 200 O e. -500 0₂-1000 03 = P3 - 150 O f. -1500 8₁-1000 03 = P₁ - 150
Following figure shows the one-line diagram of a two bus system. Take bus 1 as slack bus, bus 2 as load (PQ) bus. Neglect the shunt charging admittance. Obtain the bus admittance matrixYBUs and find V₂ and 62, power flows and line losses using FDLF method. All the values are given in per unit on 100MVA base. Use a tolerance of 0.001 for power mismatch. 1 Z12= 0.12+10.16 Slack bus V₁ 1.0/0⁰ pu 2 PL2=1.0pu Q12=0.5pu
1. FIGURE 52 shows the one-line diagram of a simple three-bus power system with generation at bus I. The voltage at bus l is V1 = 1.0L0° per unit. The scheduled loads on buses 2 and 3 are marked on the diagram. Line impedances are marked in per unit on a 100 MVA base. For the purpose of hand calculations, line resistances and line charging susceptances are neglected a) Using Gauss-Seidel method and initial estimates of Va 0)-1.0+)0 and V o)- ( 1.0 +j0, determine V2 and V3. Perform two iterations (b) If after several iterations the bus voltages converge to V20.90-j0.10 pu 0.95-70.05 pu determine the line flows and line losses and the slack bus real and reactive power. 2 400 MW 320 Mvar Slack 0.0125 0.05 300 MW 270 Mvar FIGURE 52
Q2\ The one-line diagram of a simple power system is shown in figure below. All impedances are expressed in per unit (pu) on a common MVA base. All resistances and shunt capacitances are neglected. The generators are operating on no load at their rated voltage. A three-phase fault occurs at bus 1 through a fault impedance of Zf = j0.08 per unit. Using Thevenin's theorem obtain the impedance to the point of fault and the fault current in per unit. Determine the bus voltages and line currents of generators during fault. X₁ = = 0.1 XT-0.1 3 1 to ojo XL=0.2 2 040 X₁ = 0.1
Figure shows the one-line diagram of a simple three-bus power system with generation at buses 1 and 3. The voltage at bus 1 is V1 is 1.025 at an angle of 0◦ per unit. Voltage magnitude at bus 3 is fixed at 1.03 pu with a real power generation of 300 MW. A load consisting of 400 MW and 200 MVAr is taken from bus 2. Line impedances are marked in per unit on a 100 MVA base. (a) Construct Ybus matrix for the system in Figure (b) Using Gauss-Seidel method and initial estimate of V2(0) = 1.0 + j0 and V3(0) = 1.03 + j0 and keeping |V3| = 1.03 pu, determine the phasor values of V2 and V3. Perform two iterations.
Figure below shows the single-line diagram of three-bus power system with generation at bus 1 and bus 3. The voltage at bus 1 is V₁ = 1.025/0° per unit. The voltage magnitude at bus 3 is fixed at 1.05 per unit with a real power generation of 250 MW. The scheduled load on bus 2 is marked on the diagram. Line impedances are marked in per unit on a 100 MVA base. Line resistances and line charging susceptances are neglected. By using Gauss-Seidel method and initial estimates of V₂(0) = 1.020° and V3(0) = 1.0520°, determine V₂ and V3. Perform calculation for one iteration. V₁ = 1.025/0° j0.1 Slack Bus j0.2 j0.4 j0.2 3 j0.1 250 MW 150 Mvar |V3|=1.05 P3 = 250 MW
The one line diagram of a simple three bus power system is shown in figure Each generator is represented by an emf behind the subtraction reactance. All impedances are expressed in per unit on a common MVA base. All resistances and shunt capacitances are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. Athree phase fault occurs at bus 3 through a fault impedance of Zf=j0.19 per unit. a-using thevenin’s theorem obtain the impedance to the point of fault and the fault current in per unit. b-determine the bus voltage and line currents during fault
A DC Optimal Power Flow problem is to be solved for a 3-bus network. The per-unit reactances of the lines interconnecting the buses are as follows: X12 = 0.25 pu, X13 = 0.15 pu and X23 = 0.2 pu. There is a generator at each bus. The loads at buses 1, 2 and 3 are 125 MW, 300 MW and 100 MW respectively. Bus 1 is taken as the reference bus, and SBase = 100 MVA. Which one of the below is NOT a constraint of the DCOPF problem? Select one: O a. -400 02 - 666.67 03 = P, - 125 O b. None of these C. -500 02 - 1166.67 03 = P3 - 100 d. 900 02 - 500 03 = P2 - 300
Most buses in a typical power-flow program are a.voltage controlled bus b.PQ bus c.PV bus d.Slack bus 2-The power-flow problem is the computation of voltage magnitude and phase angle at each bus in a power system under balanced three-phase steady-state conditions. False True 3-The following sequence currents were recorded in a power system under a fault condition Ipositive=j1.5pu, Inegative=–j0pu, Izero=– j0pu. The fault is a.Three-phase b.Double Line to ground c.Line to ground d.Line to line 4- he following sequence currents were recorded in a power system under a fault condition Ipositive=j1.5pu, Inegative=j0pu, Izero=j0pu. The fault is a.Three-phase b.Double Line to ground c.Line to ground d.Line to line i uploded the houndots (book )here :https://seomidea.com/hct/nu.pdf