Problem 7-1: Consider the Wheatstone bridge shown in the figure below: B R₁ 11 12 A 13 m R3 C R2 ww MRA E 卝 Basic current-sensitive Wheatstone bridge circuit (G is a galvanometer). Suppose: R3 R4 = 200 2 == R2 = variable calibrated resistor R₁ = transducer resistance = 40x + 100 (a) When x = 0, what is the value of R2 required to balance the bridge? (b) If the bridge is operated in a balanced condition in order to measure x, determine the relationship between R2 and x.

Problem 7-1: Consider the Wheatstone bridge shown in the figure below: B R₁ 11 12 A 13 m R3 C R2 ww MRA E 卝 Basic current-sensitive Wheatstone bridge circuit (G is a galvanometer). Suppose: R3 R4 = 200 2 == R2 = variable calibrated resistor R₁ = transducer resistance = 40x + 100 (a) When x = 0, what is the value of R2 required to balance the bridge? (b) If the bridge is operated in a balanced condition in order to measure x, determine the relationship between R2 and x.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q.7 a) Ring and number the junctions of component in the below circuit. R1 R2 R4 Input Output Q4 R3 b) What is the main advantage of ringing the junction W-
V1 R1 V2 Da Db R2 www V3 Given that R1=2k, R2=1k, and Da and Db are Si Diodes: a. What is V3 in terms of V1 when Da is ON? b. What is V3 in terms of V1 when Db is ON? c. What is V3 in terms of V1 when Da and Db is OFF?
BkcBZYhc850ZmX4-RzV7i6yWprtMcdra5me-w_Og/formResponse The DAC with inputs and outputs shown in figure below, the fault in the circuit is in note (all the values is in approximate range ) RF R1 200 120k U1 R2 60k R3 741 30k R4 15k - 13.2 mV - 15.6 mV - 29.9 mV -65.6 mV -79.9 mV - 82.2 mV - 96.5 mV R1 O R2 0000 0010 0100 0110 000 1001 1010 1011 1101 1110 III 0000
V - Design an ADC circuit using OPAMP (using weighted resistors)
Design a R-2R Ladder DAC using a reference voltage of (1OV) and a full scale of the output analogue voltage is (9.9975585V). If the current pass through the LSB is 1mA.1- What will be the current pass through 3rd LSB, 5th LSB and MSB. 2- Determine the Vo for an input codes (101010101010), (000101001110) and (001110010111). 4 14bit, 1mA and 6.665v, 0.9215v, 3.234v O 12bit, 1mA and 6.665v, 0.815v, 2.234v O 12bit, 1mA and 5.565v, 1.815v, 2.534v 14bit, 1mA and 6.665v, 0.8345v, 3.234v
+Vcc V1 5 D2 .tran 10 QTLP690C R8 1k Q4 2N2222 R6 1k vout Q2 2N2222 R2 470 R4 56k C2 HH 47μ VCC C1 H 47μ Astable Multivibrator R3 56k R1 470 Q1 2N2222 R5 1k D1 QTLP690C R7 1k Q3 2N2222 What is the region of operation of the circuit when the waveform is a. OV b. 4V
2/A Wheatstone bridge is excited by 12V-dc source and contain R1=1.2kN. R2-3k2, R3=2.2k2, R4 is a copper bar that has across-section area of 0.5 mm and length of 250mm(Hint the resistivity of copper is 1.7*10*Qm) Find the output voltage (E.). four tunar of ins
Reset WED W=O W =l EhD DII W=0 Derive the following state-table Present state Next state output z2zlz0 W=0 W=1 A 000 B 001 C 010 D 011 E 100
Figure shows a transistor switching circuit. Find the Vcc and Rc, which causes the output voltage to have a peak to peak value of 6V (given that the input voltage signal Vi, and the output voltage signal Vo, have units of Volt) Fone: V₁ 10k2 www +Vcc Rc V₂ B-100
4. The unbonded strain gauge accelerometer of Figure P4 natural frequency of 175 Hz and an input range of 0 to 5g. Given that the stra in due to pre-stressing is twice the maximum has a acceleration-induced strain, use the strain gauge data of Table P4 to calculate the range of the bridge output voltage*. Table P4: Data for Problem 4 Resistance = 120 Q Gauge factor =2.1 Maximum current (through any gauge)= 50 mA Length at zero acceleration =2.3 cm Acceleration due to gravity, g =9.81 m s? %3D 2 1 eo - e en +e m 4 eo - e eo +e
b) A bridge circuit is used to measure the value of the temperature using RTD. The temperature sensor is RTD100 (the resistance change form 0 22 to 100 for temperature change from 0C° to 100C°). The output voltage is measured using digital voltmeter across the bridge. Drive the relationship between the voltage across A, B with the change in resistance in the RTD due to the change in temperature. R₂ R3 R₁ B b a Rlead Read Rlead RTD (R+AR)
Determine the output of the DAC in Figure (a) if the waveforms representing a sequence of 4-bit numbers in Figure (b) are applied to the inputs. Input Do is the least significant bit (LSB). 200 kN Do o Rf 0 1 2 3 4 5 6 7 8 9 1011 1213 14 15 100 kN +5 V Do +5 V 10 k2 I 50 kN OVout D1 +5 V D2 o D2 +5 V 25 kN D3 0 D3 (a) (b)