FL b FL What is the change in length (L) of the titanium bar (E = 16.5E6 psi) given: L = 36 in., b = 3 in., h = 0.25 in, and F = 3 kips Answer to above question is 8.72E-3 in, the shear modulus for the bar is 6.145E6 psi, poisons ratio is 0.343. My question is what is the strain (in macrostrain) in the bar in a direction perpendicular to the direction of the applied force? (Answer is 82.8, I need to understand how to reach this answer.)

FL b FL What is the change in length (L) of the titanium bar (E = 16.5E6 psi) given: L = 36 in., b = 3 in., h = 0.25 in, and F = 3 kips Answer to above question is 8.72E-3 in, the shear modulus for the bar is 6.145E6 psi, poisons ratio is 0.343. My question is what is the strain (in macrostrain) in the bar in a direction perpendicular to the direction of the applied force? (Answer is 82.8, I need to understand how to reach this answer.)

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2P

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
An aluminum pipe must not stretch more than 0.05in when it issubjected to a tensile load. Knowing that E=10.1x10^6psi and that the maximum allowable normal stress is 14ksi, determine (a) the maximum allowable length of the pipe, and (b) the required area of the pipe if the tensile load is 127.5kips.
The compound bar, composed ot the three segments shown, is initially stress-free. Compute the stress in the Steel segment if the temperature drops 25°C. Assume that the walls do not yield and use the following data: A (mm²) a (/°C) 11.7x10-6 E (GPa) Steel 800 200 Bronze 1400 19.0 x10-6 83 Aluminum 2000 23. 0 x10-6 70 800 mm 500 mm- -400 mm→ Steel Bronze Aluminum Select one: O a. 11.94 MPa O b. 59.21 MPa O c. 78.95 MPa O d. 15.92 MPa Next page
a) What is the stress in the bronze rod (in MPa)?b) What is the stress in the steel rod (in MPa)?
Part A An aluminum 2014-T4 alloy bar 2.50 inches wide and 0.750 inches in thickness has a 1/4 inch radius hole centered on its width, as shown in the sketch. With an axial load, P = 8650 lbs applied, the maximum axial stress at the edges of the hole was experimentally determined to be 7670 psi What is the stress concentration factor, K, of the hole? 1.33 0.75 1.66 1.50 P 2.50 in. -Radius 1/4 in. P= 8650 lbs
PROBLEM 3-18 GIVEN: A tension test was performed on a magnesium alloy specimen having a diameter 0.5 in. and gage length of 2 in. The resulting stress-strain diagram is shown in the figure. or (ksi) 4(0) 25 15 0.008 REQUIRED: If the specimen is stressed to 30 ksi and unloaded, determine the permanent elongation of the specimen.
2.58 Knowing that a 0.02-in. gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the aluminum bar will be equal to 11 ksi, (b) the corresponding exact length of the aluminum bar. 0.02 in. 14 in. 18 in. ਕਰ Bronze A = 2.4 in² E-15 x 105 psi a = 12 x 10-6/"F Aluminum A = 2.8 in² E = 10.6 x 105 psi a = 12.9 × 10-5/"F
A compound bar is subjected to a compressive force of P=556 kN by means of a rigid endplate at the top. If the length of the bar is 876mm, determine the stress in the alurninum core. Answer in MPa. Round off your final answer to 2 decimal places. 25 mm Brass core E = 105 GPa a = 20.9 x 10-6/°C Aluminum shell E = 70 GPa Q = 23.6 x 10-6/°C 60 mm