Problem 38 A 400 n resistor is connected in parallel to a coil having a resistance of 10 0 and an inductance of 3H. If a single-phase AC voltage source having an instantaneous value of v(t) = 35 sin(50t) V is connected across the parallel connection, look for the ff: a. The phasor and instantaneous current across the coil? b. The phasor and instantaneous current across the 400n resistor c. The total impedance of the connection d. The phasor diagram showing the phase difference of the source voltage and the total current

Problem 38 A 400 n resistor is connected in parallel to a coil having a resistance of 10 0 and an inductance of 3H. If a single-phase AC voltage source having an instantaneous value of v(t) = 35 sin(50t) V is connected across the parallel connection, look for the ff: a. The phasor and instantaneous current across the coil? b. The phasor and instantaneous current across the 400n resistor c. The total impedance of the connection d. The phasor diagram showing the phase difference of the source voltage and the total current

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
The below figure shows the waveform of the voltage and current in a purcly inductive AC circuit. Voltage Current Using the voltage phasor as the reference, the current phasor O Is in phase with the voltage Lags by 90° O Leads by 90° Lags and then leads by 160°
60. Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V de voltage source. 61 Datermine the volto in the girRuit F Figura 1 1?
For figure (1)draw and calculate the voltages waveform across each half of secondary winding and across load when 100sin2π60t applied across the primary, then find PIV.
Draw roughly the arc characteristics in alternating currents with a frequency of 50 Hz and 500 Hz, explain briefly
QUESTION 3 An inductor, a capacitor, and a resistor are connected in parallel with a function generator. The inductor draws 100mA RMS, the capacitor draws 150mA RMS, and the resistor draws 200mA RMS. Find the magnitude of the total current. O 450mA RMS O 544mA RMS O 352mA RMS O 206mA RMS
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
A resistor R and a capacitor C are connected in series across a 400 V variable ac supply. When the frequency is 40 Hz, it draws 10 A current, and when the frequency is 50 Hz, it draws 15 A current. Find R and C.
d) 3-A 500 ohm resistor is connected in series with a coil with a self-inductance of 800 mH and the maximum It is fed by a sinusoidal source with an amplitude of 15 V and a frequency of 15.92 Hz. According to this Which of the following can represent the voltage across the coil? 14.81cos(wt - 9.09) V 2.5cos(wt - 21.2) V 7.20cos(wt - 11.45) V 2.37cos(wt - 81) V 8.5cos(wt - 41.2) V leave blank 3075
What is the relationship between R, L, and C components in a series AC circuit?