t=0 V. A impedance of Z = 25453.13°Q is connected across a source with a voltage of 169.706 sin (157.080t) volts For the circuit, find the ff.: (a) R, (b) X, (c) voltage polar form, (d) current polar form, (e) current waveform equation, (f) simplified power waveform equation.

t=0 V. A impedance of Z = 25453.13°Q is connected across a source with a voltage of 169.706 sin (157.080t) volts For the circuit, find the ff.: (a) R, (b) X, (c) voltage polar form, (d) current polar form, (e) current waveform equation, (f) simplified power waveform equation.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Related questions

Q: (b) Given that a total impedance of a series circuit is Z = 10 – j13 Q and the operating frequency…

A: In this question, Total impedance Z= 10-13j Operating frequency f= 60Hz. Sketch the series and…

Q: O At the value of K where the system is marginally stable, what are the pole locations? 15j, -6 15j,…

Q: For the given circuit, Is 2 kW 1kVar (cap.) + 2 kV A 4 kW 0 + j100Vrms (~ 0.7pf leading 0.9pf…

Q: 3. A 100 µF capacitor, a 4.0 H inductor and a 35 Qresistor are connected in series with an…

Q: 10. A. Find the impedance between terminals a and b in the circuit below if it operates at steady…

A: Given data: Angular frequency = 2000 rad/s L=5 mH R2=20 Ω R1=5 Ω C=25 μF v(t)=10cos2000t (a)…

Q: Consider the circuit diagram where Vs = 2300 20 Vrms V, z, Z, Find: 1. The apparent power delivered…

Q: The total impedance Z, of a circuit containung an inductor with inductance L and resistance R in…

A: we need to find out R and L.

Q: A parallel connection of a resistor, inductor and capacitor is presented in the figure below. The…

Q: 1. For the following circuit derive the equation for the power factor, where the conducting angle a…

Q: Discuss the following term in reactive circuit? a) Real power b) Apparent power G) Power factor 1.

Q: The device is represented in the frequency domain bya Norton equivalent. When a resistor having an…

A: Given: The device is represented in the frequency domain by a Norton equivalent. When a resistor…

Q: For the given circuit, Is 2 kW 1kV ar (cap.) 2 kV A 4 kW 0+ j100Vrms |0.7pf leading 0.9pf lagging…

Q: A load connected to a 120 Vrm source is drawing 1,600 VA at 0.6 power factor lag. a) What is the…

Q: A SERIES RC CIRCUIT TAKES A CURRENT WHOSE EQUATION Is 2 sin (754t+40) AMPERE. WHEN CONNECTED TO A…

Q: + V1 10Vrms J50Hz 0° V1 = 10 /0° R1 100 Ω L1 160mH C1 :320μF

Q: (a) For the circuit shown in Figure Q5.1 determine the angular frequency of the sinusoidal supply…

A: a) find the angular frequency of the supply voltage in order to maximize the active Power…

Q: (a) Calculate the input impedance of the infinite ladder network shown in the figure below. (Z =…

A: (a) Since, the given circuit is of the infinite length and the total impedance of the circuit will…

Q: 2. A delta-connected load with 500 resistance, 209mH inductance and 50µF capacitance in series per…

A: In this question we need to find a phase current of the given three phase circuit.

Q: Consider the network depicted in the following figure, and determine the equivalent impedance seen…

Q: 1 In the circuit of Figure. Z, = 60Z– 30°N · and· Z, = 40Z45°Q. %3D (1)-Find the phasors İ,,İ‚‚İ¸.…

A: Given circuit,

Q: 10 2 13.263 mH 73.683 µF Figure #6 Figure #6 shows an impedance consisting of resistance, inductance…

A: (a) Write the expression for the voltage when the frequency is in third harmonics and then find the…

Q: Suppose that the current, i, through a resistor is described by the function i(t) = (60 – t)? + (60…

Q: (a) If the time domain expression for the source is i, = 0.04 cos(1250t) amps, find the phasor…

A: In this question we will find phasor expression of Io and equivalent impedance seen by the source...

Q: FN.Q3- In the RLC circuit, vs(t) = 330.Sin(628t) Volt, R= 470, C=220µF andL=65 mH. Determine the…

Q: five infinite-impedance volunteers,calibrated to read rms values,are connected as shown below. let…

A: First, convert the parameter of the passive elements connected in the circuit in the same unit in…

Q: Consider the circuit diagram where Vs = 2300 20 Vrms z, Z, Find: 1. The apparent power delivered by…

Q: Question: (a) Find the input impedance. Zin, of the circuit shown below by using the concept of…

A: Here, we have given a circuit, for which we have to calculate the input impedance, Zin by using the…

Q: R1 3 kN L1 3 mH ww C1 R3 1 kN v(t) 6 μF R2 2 kN ww

Q: In an electric power system, it is given that the effective impedance of the generator station is Rs…

Q: HW # 7.1 Vp = 50 sin(@t), R1 = 1kN , If the firing angle is 30°, draw %3D Vp=Vm sinot R Vo the…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: Unless given, use the: POLAR FORM for voltage and current, RECTANGULAR FORM for impedance. Consider…

Q: a) A single-phase AC waveform is represented by the equation; v(t) = 400 sin(3142t + 0.25) V…

Q: 500Ω ΙμF 1) a) The frequency of the source voltage in the circuit in the figure is adjusted until i,…

Q: A 90-ohm resistor, a 32 mH inductor, and a 5 uF capacitor are connected in series across the…

Q: A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad.…

Q: Ex. Determine; Z, I, p.f., Pr,, Q, and S T» 30 ohms j40 ohms E =200V F = 60 Hz 30 ohms 20 ohms j70…

Q: Unless given, use the: POLAR FORM for voltage and current, RECTANGULAR FORM for impedance. Consider…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Consider the circuit diagram where Vs = 230020 Vrms Z, Z, Z, Find: 1. The apparent power delivered…

Q: Suppose that an inductor (L) - resistor (R) – capacitor (C) circuit is connected to an AC source…

Q: 6. A single-phase AC/AC voltage controller is shown in Fig. 10, inductive load, R=6n, x, = 82,…

A: Figure shows two thyristor connected with a resistance and inductor having its own value. Delay…

Q: In the Transmission Line Simulator, th Transmission Line is composed of wh parameter/s? O A. The…

A: Transmission line simulator useful to know behaviour of transmission line under various load…

Q: A series circuit of RLC with following parameters, R=15 ohm, L-20 m H Farad. VT=169.7 sin (337t-30)…

Q: For the circuit shown below, Given that V 100Z0°Vm and I = 30245°Ams then the values of P, and Q3…

A: Given circuit shown below Vs=100∠0° VrmsIs=30∠45° Arms

Q: IV. A impedance of Z = 25453.13°Q is connected across a source with a voltage of 169.706 sin…

Q: Three currents i,, i, and i, are approaching a node. If i, = 10 sin (400t + 60°) A, and i, = 10 sin…

A: In this question we will find current i 3...

Q: 2) The amplitude of the emf in the below circuit is 150V, while the angular frequency is 60x. The…

Question

Need asap

t= 0
IV. A impedance of Z = 25453.13° Q is connected across a source with a voltage of 169.706 sin (157.080t) volts.
For the circuit, find the ff.: (a) R, (b) X, (c) voltage polar form, (d) current polar form, (e) current waveform
equation, (f) simplified power waveform equation.
V. A series circuit of two pure elements has the following applied voltages and resulting currents of 162.635

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What impedance vector (0- j15) Ohms represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a capacitance.
A chopper circuit has an inductive load of 2ohm resistance and 10mH inductance. If the source voltage is 20 V and the frequency of the chopper is set to 100Hz and the on-time to 5 ms. Determine the average voltage and current, maximum and minimum load currents.
What impedance vector - j25 represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a resistance.
Impedance...
Q4/ Find the voltage average and the voltage waveform for the output of the circuit shown below. Vi=120v (rms) 2.1kr. V. to
A 230 V, 50 Hz a.c. supply is applied to a coil of 0.06 H inductance and 2.5 resistance connected in series with a 6.8 F capacitor. Calculate impedance and power consumption and power factor. Now ,In above a.c. circuit, A inductor of 0.2H is connected in parallel with the power supply, find new power factor and power consumption.
1. Enumerate five formulas for series-parallel capacitances across Vt source and draw the circuit. 2. Enumerate five formulas for parallel-series capacitances across Vt source and draw the circuit.
A DC-DC Chopper Circuit with an RL Load has an output current waveform shown below with a duty cycle of 50% and 1ms period. If it has a resistance of 1ohm and an inductance of 10mH, find the source voltage. 5A 2A ton toff output _current
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
A DC-DC Chopper Circuit with an RL Load has an output current waveform shown below with a duty cycle of 50% and 1ms period. If it has a resistance of lohm and an inductance of 10mH, find the source voltage. output 5A -current 2A ten toff
A certain impedance is given by 1012° N. Does the current lead or lag the voltage, and by how many degrees? Fill in the blanks. The current the voltage by
A step-down chopper is to be used to supply power from a 600-V overhead wire to the commutator motor on a trolley bus. The motor may be mod- eled as a generated direct voltage in series with a resistance of 0.2 and an inductance of 25 mH. The frequency of the chopper is set at 500 Hz. (a) When the bus is stopped, what should be the ON time of the chopper to provide a motor current of 150 A? (b) What is the maximum possible generated voltage of the motor for which a current of 150 A can be supplied? (c) What is the average value of the supply current for the conditions of (a) and (b)? បទៅនឹងរស់របស (d) If the motor current is to be continuous, what should be its minimum. value?