Prob. 3.9-3. The five-segment stepped rod shown in Fig. P3.9- 3 is stress free when it is attached to rigid supports at ends A and F. Subsequently, it is subjected to two external loads of magnitude P at nodes B and D, as shown in Fig. P3.9-3. The bar is homogeneous with modulus of elasticity E, and the cross-sectional areas are A₁ = A5 = A, and A₂ = A4 = 2A, and A3 = 3A. Use the Force Method to solve for the reaction PF at end F. (Hint: Let PF = F5 be the redundant force, and use the Force Method to solve directly for this force.) (1) P B (2) ·L——— L. c (3) P P3.9-3 D (4) E (5) F PF

Prob. 3.9-3. The five-segment stepped rod shown in Fig. P3.9- 3 is stress free when it is attached to rigid supports at ends A and F. Subsequently, it is subjected to two external loads of magnitude P at nodes B and D, as shown in Fig. P3.9-3. The bar is homogeneous with modulus of elasticity E, and the cross-sectional areas are A₁ = A5 = A, and A₂ = A4 = 2A, and A3 = 3A. Use the Force Method to solve for the reaction PF at end F. (Hint: Let PF = F5 be the redundant force, and use the Force Method to solve directly for this force.) (1) P B (2) ·L——— L. c (3) P P3.9-3 D (4) E (5) F PF

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated load P is applied to the free end of aluminum rod (3). Bronze rod (1) has an elastic modulus of E1 = 15,000 ksi and a diameter of d1 = 0.60 in. Aluminum rod (2) has an elastic modulus of E2 = 10,000 ksi and a diameter of d2 = 0.70in. Aluminum rod (3) has a diameter of d3 = 1.00in. The yield strength of the bronze is 48 ksi and the yield strength of the aluminum is 40 ksi. Assume a = 2.5 ft, b = 1.5 ft, L1 = 6 ft, L2 = 8 ft, and L3 = 3 ft.(a) Determine the magnitude of load P that can safely be applied to the structure if a minimum factor of safety of 2.2 is required.(b) Determine the deflection of point D for the load determined in part (a).(c) The pin used at B has an ultimate shear strength of 50 ksi. If a factor of safety of 3.4 is required for this double shear pin connection, determine the minimum pin diameter that can be used at B.
A rigid bar AB is hinged at A and supported by copper rod 2 m long and steel rod i m long as shown in fig. the bar carries a load of 20 KN at B. the cross section areas of steel and copper are 200 mm2 and 400 mm2 respectively find the stress in each rod ?if Es=210 GPa and Ec=83 GPa Copper rod 2m Steel rod- -1 m- 1m 2 m m- B 20 KN
Prob. 2.9-10. At room temperature (70°F) and with no axial load (P = 0) the extensional strain of the prismatic bar (Fig. P2.9-10) in the axial direction is zero, that is, € = 0. Subsequently, the bar is heated to 120°F and a tensile load P is applied. The material properties for the bar are: E = 10 × 10³ ksi and a = 13 x 10-6/F, and the cross-sectional area of the bar is 1.8 in². For the latter load-temperature condi- tion, the extensional strain is found to be €x = 900 × 10 6. (a) Determine the value of the axial tensile load P. (b) De- termine the normal stress and the shear stress on the oblique plane NN'. (Note: The total strain is the sum of strain asso- ciated with normal stress o (Eq. 2.14) and the strain due to change of temperature AT (Eq. 2.8).) in. P Gage measures extensional strain Ex N N' 25° P2.9-10 X
4.3. At a point in a structural member, yielding occurred under a state of stress given by: 40 40 50 -60 MPa -60 Determine the uni-axial tensile yield strength of the material according to (a) maximum shearing stress theory, and (b) Octahedral shearing stress theory. 4.5. Determine the width t of the cantilever of height 2t and length 0.25 m subjected to a 450 N concentrated force at its free end. Apply the maximum energy of distortion theory. The tensile and compressive strengths of the material are both 280 MPa. 4.6. Determine the required diameter of a steel transmission shaft 10 m in length and of yield strength 350 MPa. In order to resist a torque of up to 500 N.m. The shaft is supported by frictionless bearings at its ends. Design the shaft according to the maximum shear stress theory, selecting a factor of safety of 1.5, (a) neglecting the shaft weight, and (b) including the effect of shaft weight. Use y = 77 kN/m as the weight per unit volume of steel. 190 MPa 30 MPa 40 MPa…
The assembly in Fig. P-242 consists of a light rigid bar AB, pinned at O, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support. A 0.75 m O Steel A = 250 mm² E = 200 GPa 1.5 m Figure P-242 Aluminum L = 2 m A = 300 mm² E = 70 GPa B
The steel rod is placed inside the copper tube, the length of each being exactly 15 in. If the assembly is compressed by 0.0075 in., determine the stress in each component and the applied force P. The moduli of elasticity are 29x10^6 psi for steeland 17x10^6 psi for copper. 15 in. -0.6 in. -0.75 in. -0.125 in. FIG. P2.10
Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated load P is applied to the free end of aluminum rod (3). Bronze rod (1) has an elastic modulus of E1 = 15,000 ksi and a diameter of d1 = 0.45 in. Aluminum rod (2) has an elastic modulus of E2 = 10,000 ksi and a diameter of d2 = 0.75in. Aluminum rod (3) has a diameter of d3 = 0.95in. The yield strength of the bronze is 48 ksi and the yield strength of the aluminum is 40 ksi. Assume a = 2.5 ft, b = 1.5 ft, L1 = 6 ft, L2 = 8 ft, and L3 = 3 ft.FIND: (a) Calculate the cross-sectional areas of the three rods.(b) For a factor of safety of 1.9, calculate the allowable stresses in the bronze and the aluminum rods. (c) On a piece of paper, sketch a free body diagram (FBD) cut through rod (3) and also a FBD of the rigid bar. Using these, find a relationship between the force in rod 1 (F1) and the applied load, P, a relationship between the force in rod 2 (F2) and the applied load, P, and also a relationship…
A 200 kN force is applied at the free end of the cantilever beam as shown in the figure below. What is the maximum value of stress induced in the top fibre of cantilever by the applied force at section B-B? 300 mm 10 mm В 200 kN 10 mm 500 mm В 2 m 10 mm 300 mm
2.47 The negligible weight rigid bar is pinned at O and attached to two vertical rods. WI is the largest load P that can be applied without exceeding stresses of 150 MPa in t steel rod and 70 MPa in the bronze rod, assuming the rods were initially stress-free? 4m 3m 3m Steel A = 600mm2 E = 83Gpa L = 4m Steel V P A = 1800mm2 E = 200Gpa L 3m
PROBLEM 07: The figure shows a truss and the sequence of assembly of members at pins H, G, and F. All members of the truss have cross-sectional areas of 250mm2 and all pins have diameters of 15mm. Determine the following: a. Axial stresses in members HA, HB, HG, and HC. b. The maximum shear stress in pin H. G H HC HG HB HA GF A 130° B 30 E GH +3 m--3 m→-3 m-→--3 m- ¥4 kN V2 kN ¥3 kN Pin H Pin G Pin F
Q1 A truss system is shown in Figure Q1. It is loaded at joints D and E as shown. The truss members are to be manufactured from Aluminium Alloy cylindrical bar with a tensile yield stress of 300 MPa, a compressive yield stress of 200 MPa, and Young's Modulus of 70 GPa. 1.5m 1.5m A B 4001 10 KN 3m Fig. Q1 E 水 20 KN 1.5m D ➜ (a) Show that the truss system can be described as statically determinate. (b) Draw a Free Body Diagram of the truss and determine the reactions at the supports. (c) Use the METHOD OF JOINTS to determine the load in each member of the truss, indicating whether they are tensile or compressive.
The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute values of the deformation at point A, B, C, D