2.47 The negligible weight rigid bar is pinned at O and attached to two vertical rods. WIis the largest load P that can be applied without exceeding stresses of 150 MPa in tsteel rod and 70 MPa in the bronze rod, assuming the rods were initially stress-free?4m3m3mSteelA = 600mm2E = 83GpaL = 4mSteelV PA = 1800mm2E = 200GpaL 3m

The minimum Value of P is adopted means we take P = 221.072 Kn The rods are assuming stress free.…

2.47 The negligible weight rigid bar is pinned at O and attached to two vertical rods. W is the largest load P that can be applied without exceeding stresses of 150 MPa in steel rod and 70 MPa in the bronze rod, assuming the rods were initially stress-free? 4m 3m 3m Steel A = 600mm2 E = 83Gpa L= 4m Steel V P A = 1800mm2 E = 200Gpa L= 3m

2.47 The negligible weight rigid bar is pinned at O and attached to two vertical rods. W is the largest load P that can be applied without exceeding stresses of 150 MPa in steel rod and 70 MPa in the bronze rod, assuming the rods were initially stress-free? 4m 3m 3m Steel A = 600mm2 E = 83Gpa L= 4m Steel V P A = 1800mm2 E = 200Gpa L= 3m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two vertical forces are applied to a beam of the cross section shown in Fig.2. Determine the maximum tensile and compressive stresses in portion BC of the beam.(Take R=h=25mm). 4 kN 4KN -le A What B 300 mm 300 mm
2. The following the truss figure, came from your Module 1. Page 9. B D F 3 m H H. E G 30 kN 70 kN 4 panels at 4 m = 16 m But this time, All the members have a cross sectional area of 850 mm². Find the normal stress of the following members а. EF b. GH c. DF
3. The rigid bar weighs 5 kN/m, is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises 20°C after a load W = 150 kN is applied. A (mm?) a (FC) E (GPa) Steel rod 300 11.7 x 10-6 200 Bronze rod 1400 18.9 x 10-6 83 Bronze | 3 m Steel 1.5 m ►| 1.0 m 2.5 m 2 m W
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontalbefore the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. STEEL Lm A-400 mm E-200 GPa BRONZE L-5m A-500 mm E-80 GPa 3m
The three suspender bars are made of A992 steel and have equal cross-sectional areas of 450 mm2. Determine the average normal stress in each bar if the rigid beam is subjected to the loading shown. Use E = 200 GPa B 60 kN 2 m 40 kN E F1m--1m--1 m--1m-
QUESTION 2 The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends If there is no load in the members when T1 = 50'F, determine the average normal stress in each member when T2 = 120°F Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in? 3 ft 2 ft
Q4) A cast iron beam is of I – section as shown in Figure (3). The beam is simply supported on a span of 5 m. If the tensile stress is not to exceed 20 N/mm2, find the safe uniformly load which the beam can carry. Find also the maximum compressive stress. I 80 mm- 20 mm 3 169.34 mm 200 mm 2) 20 mm A 90.66 mm 40 mm 100 mm Figure (3)
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the loadP 20 KN is applied. 15m What is the axial deformation of stecl rod in mm?
Determine the normal stress (in Mpa) in member AB of the truss shown if it is made up of a 14-mm-square bar of alloy and the load P is 21.53 kN. Express your answer in two decimal places.
Determine the maximum permissible value of T provided the allowable shearing stresses in brass and steel are 70 and 110 MPa, respectively. The outer and inner diameters are 90 mm and 70 mm, respectively. G for brass and steel are 40 GPa and 80 GPa, respectively. В C E Legend: Brass Steel 1 m 1 m 1 m 1 m
The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. Knowing that the modulus of rigidity is 3.7E6 psi for aluminum and 5.6E6 psi for brass, determine the maximum shearing stress in cylinder AB And cylinder BC in ksi. 1 Aluminum T= 19.6 kip-in. Brass A - 1.4 in. B <-2.1 in. C 10 in. 15 in.
2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Specify whether tension or compression. Bronze Aluminum Steel A =400 mm2 A= 600 mm2 A = 300 mm2 2P ЗР 4P P -3 m 5 m 4 m Stress in Bronze (MPa) %D Stress in Aluminum (MPa) %3D Stress in Steel (MPa)