Answered: Percent Passing Size 25 19 12.5 9.5…

Percent Passing Size 25 19 12.5 9.5 4.75 1.18 0.60 0.30 0.15 mm mm mm mm mm mm mm mm 42 Aggregate A Aggregate B 100 100 100 77 70 34 28 20 62 43 100 85 24 13 84 Aggregate C 100 100 51 29 19 8 14

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3. For a particular aggregate, the bulk specific gravity (Dry) was 2.67,the porosity was 3%, and the…

Q: From the given data shown in the table below, determine the effective specific gravity of…

A: Given, SG of FA = 2.627 SG of CA = 2.706 SG of asphalt = 1.012

Q: Laboratory specific gravity and absorption tests are run on two coarse aggregate sizes, which have…

A: awe know that Specific gravity of mixure isGmix=WA+WBWAGA+WBGBWA=40% and WB=60%

Q: Absorption of coarse aggregate 1.8% Moisture content in coarse aggregate 2.3% Dry weight of fine…

A: Amount of water contributed by coarse =MC-ABS×WTWC=0.023-0.018×1500=7.5lb

Q: The mass of fine aggregate B has been reduced and weighed to conduct an aggregate test shown in…

Q: The following table shows the results obtained from Wash Test done on samples of fine aggregates.…

Q: Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced…

Q: For the structure loaded as shown below, derive the expressions that give: a) The horizontal…

A: Solution: Considering the diagram:

Q: Solve the axial bar forces of the truss shown and the missing forces. Identify whether it's…

A: Given data in question Load Dimension Angle To find out Member forces

Q: 1) Using the information from tables 1 and 2 below, calculate the cumulative percentage passing for…

A: Sieve Mass % Cumulative % Cumulative % No Sieve size Retained mass Retained Retained Passing…

Q: In an aggregate mix, the proportions of coarse aggregate, fine aggregate and mineral filler are 55%,…

Q: The grading of three aggregates is given below. a) Calculate the percent passing for a combined…

A: Given: Results of gradation tests on three aggregate A,B and C is shown below Sieve size…

Q: 1)Determine the uncorrected and corrected weights based on the following data using the traditional…

A: Following is required mix design procedure :

Q: Q-If aggregates completely pass through a sieve of size 75 mm and are retained on a sieve of size 60…

A: given- Given aggregate completely passes through 75 mm size sieve & retained on 60 mm size…

Q: What is the amount of Moist Coarse Aggregate? b. What is the amount of SSD Fine Aggregate? c.…

A: Solution: Givendata coarse aggregate = 1160 kg/m3 fine aggregate = 599 kg/m3 water content = 148…

Q: 7) The grading of three aggregates is given below. a) Calculate the percent passing for a combined…

A: Aggregate is a granular material which is generally known by names such as sans or gravel. It is an…

Q: Q3) The result of sieve analysis of a sample of aggregate given in the Table below. According to…

A: According to ASTM C 33 Sieve analysis, the allowable aggregate sample should follow the below…

Q: Laboratory specific gravity and absorption tests are run on two coarse aggre-gate sizes, which have…

A: Given: Aggregate A: Bulk specific gravity = 2.814 Absorption = 0.4, Aggregate B: Bulk specific…

Q: sp wt of SSD CA = 6135 g wt of submerged CA = 3901 g wt of oven-dry CA = 6008 g Calculate the bulk…

A: A=weight of oven dry coarse aggregate B=weight of SSD coarse aggregate C=weight of submerged coarse…

Q: only as specified by the instruct 5.10 Samples of coarse aggregate from a stockpile are brought to…

Q: Q3) The result of sieve analysis of a sample of aggregate given in the Table below. According to…

A: Sieve analysis: It is an analytical method that is used to determine the particle size distribution…

Q: In an aggregate mix, the proportions of coarse aggregate, fine aggregate and mineral filler are 55%,…

Q: Aggregates completely fill-up the 1 cubic meter container. If the mass of coarse aggregate inside…

A: Given:Volume of container= 1 cubic metreMass of coarse aggregate= 2010 kgSpecific gravity of coarse…

Q: For a fine aggregate, the value of fineness modulus was calculated to be 2.30. Is the particle size…

A: Fineness modulus indicates how coarse or fine an aggregate is. Higher the fineness modulus coarser…

Q: gravity=2.60, SSD Bulk Specific Gravity=2.63, apparent Specific gravity= 2.68, percent…

A: Specific gravity generally gives the information regarding the denseness of the aggregates.So,more…

Q: Aggregates completely fill-up the 1 cubic meter container. If the mass of coarse aggregate inside…

A: Given:Volume of container= 1 cubic metreMass of coarse aggregate= 2010 kgSpecific gravity of coarse…

Q: Volume of measure, (ft³) Weight of measure (lb) Weight of measure + aggrega

Q: Aggregates from three sources having the properties shown in the table below where blended at a…

A: We have to determine the properties of aggregate blend for the data given in the problem. Below I…

Q: The mass of aggregate B has been reduced and weighed to conduct an aggregate test shown in Table 2.…

A: Solution: Given: Mass of Aggregate: 500.8g SSD Mass of Aggregate: 500.2g Mass of pycnometer with…

Q: The mass of the aggregates to be tested in Los Angeles Abrasion Machine is 10,000g, what is the %…

Q: Three types of aggregate have sieve analysis as given below. Combine these types of aggregate to…

A: Sieve, inches3/41/23/8No.4No.8No.30No. 50No. 100No.…

Q: In an aggregate mix, the proportions of coarse aggregate, fine aggregate and mineral filler are 55%,…

Q: It is given that an aggregate mix has 260 grams of coarse aggregates and 240 grams of fine…

Q: Laboratory specific gravity and absorption tests are run on two coarse aggre-gate sizes, which have…

A: Given that Bulk specific gravity of aggregate A is GA= 2.491 and absorption is 0.8 Bulk specific…

Q: Determine the suitability of the aggregate, with the gradation tabulated below, for use in Portland…

Q: Specific Gravity and Absorption of Coarse Aggregates What are the possible discussion of…

A: There are two types of aggregates, they are fine aggregate and coarse aggregate. Coarse aggregate…

Q: After placement, the temperature of the concrete is measured and recorded by thermal sensors during…

A: Datum Temperature of concrete mix = -50 CTemperature vs age data for first 14 days

Q: Prepare report about one of the following topics about aggregate:

A: Soundness of Aggregate: The soundness (AASHTO T104) refers to the durability of an aggregate in…

Q: Given the bulk specific gravities of 2.65 for coarse aggregate, 2.69 for fine aggregate, and 2.73…

Q: Determine the difference between the Rodded and Loose Unit Weight of aggregates

A: Difference between Rodded and Loose unit weight

Q: The wet mass of an aggregate sample is 583g and its dry mass is 575g. The test shows the absorption…

A: Finding out the type of moisture condition.

Question

Table shows the grain size distributions of aggregates A, B, and C. The three aggregates must be blended at a ratio of 15:25:60 by weight, respectively.Using a spreadsheet program, determine the grain size distribution of the blend.

Percent Passing
Size
25
19
12.5
9.5
4.75
1.18
0.60
0.30
0.15
mm
mm
mm
mm
mm
mm
mm
mm
42
Aggregate A
Aggregate B
100
100
100
77
70
34
28
20
62
43
100
85
24
13
84
Aggregate C
100
100
51
29
19
8
14

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please show step by step calculation of each value
Use the following data:Oven Dry weight - 4.98 kgWeight under water - 3.02 kgSSD Weight - 5.07 kg1. Determine the apparent specific gravity of the coarse aggregates.2.Determine the bulk specific gravity SSD of the coarse aggregates3.Determine the bulk specific gravity (Dry) of the coarse aggregates4.
The equation of deformation is derived to be y = x³ - xL for a beam shown in the figure. YA The curvature of the beam at the mid-span
Can you please write how did you come up with the answer
Referring to the aggregate gradations A, B, and C in Figure , answer the following questions:a. What is the maximum size of each gradation?b. What is the nominal maximum size of each gradation?c. Classify each gradation as dense, open, or gap indicating the reason for each classification.
Show complete process. Aggregates from three sources having the properties shown in the table below where blended at a ratio of 30:45:25 by weight. Determine the properties of the aggregate blend.
What is the most widely used aggregate type in Turkey. Classify it according to : - source, - shape, - geological origin, - specific gravity, - reactivity,
Moving to another question will Sav estion 14 There are two sources of aggregates (A, B). A sample has been taken from both sources and measured their mass as shown in table b Aggregate A 500 Aggregate B 600 564 480 Measurement Wet mass (9) Oven-dry mass (g) (a) Determine the total moisture content for the samples from both aggregate sources, respectively. (b) Determine the total moisture content for an aggregate blend with 30% of aggregate A and 70% of aggregate B. Attach File Browse Local Files Browse Content Collection
After placement, the temperature of the concrete was measured and recorded by thermal sensors during the first 7 days. The temperature change with time is given in the figure below and the datum temperature of the concrete mix is known to be -5°C. If formworks are planned to be removed when 70% of maturity of the laboratory samples cured at 20 °C for 7 days is reached, what is the formwork removal time? temperature (°C) 30 28 26 mm O d. 24 O e 22 20 18 16 14 12 10 OaEarlier than 3.5 days 0 12 24 36 Ob Between 40 to 45 days OF Between 4.5 to 5 days Between 3.5 to 4 days Later that 5 days 48 60 72 84 96 108 120 132 144 156 168 age (hour)
Referring to the aggregate gradations A, B, and C in Figure P5.26, answer the following questions: a. What is the maximum size of each gradation? b. What is the nominal maximum size of each gradation? c. Classify each gradation as dense, open, or gap indicating the reason for each classification. 100 A 80- 60 40 0.075 0.30 1.18 2.36 4.75 9.5 12.5 19.0 25.0 0.15 0.60 Sieve sizes (mm) FIGURE P5.26 Percent passing 20
4-33. Following are results of gradation tests on three aggregates: Aggregate A 100% 92% 41% 19% 7% 4% 2% 1% Passing 25 mm (1 in.) 19 mm (3/4 in.) 9.5 mm (3/8 in.) 4.75 mm (No. 4) 2.36 mm (No. 8) 600 μm (No. 30) 300 μm (No. 50) 75 μm (No. 200) Aggregate B 100% 77% 60% 42% 36% 28% Aggregate C 100% 96% 79% 40% 16% 3% Combine these to give a gradation falling approximately in the center of the specification given in Section 4-5.1.
The mass of a bulk density bucket is measured as 2115 g when it is empty. The mass of the bucket when filled with water is 5148 g. The bucket is filled with aggregates and the total mass of the bucket and aggregate is measured as 7073 g. Calculate the bulk density of the aggregate.