Patm A water Tank C hi h2 As shown in the figure, at hi= 1.8 m, h2= 3.6 m positions, the water in the tank is discharged by means of a pump. The diameter of the pipe is D= 75 mm. Since the ambient pressure is 10 bar, calculate the velocity of the water in the pipe, the flow rate of the system and the absolute pressure at the peak (point B), ignoring all friction losses. Patin Note: If you find it necessary to solve the problem, you can make assumptions. But you must write down your assumptions. Take the gravity as g- 9.806 m/s² Hint: You can start with using Bernoulli Equation for A and C points.

Patm A water Tank C hi h2 As shown in the figure, at hi= 1.8 m, h2= 3.6 m positions, the water in the tank is discharged by means of a pump. The diameter of the pipe is D= 75 mm. Since the ambient pressure is 10 bar, calculate the velocity of the water in the pipe, the flow rate of the system and the absolute pressure at the peak (point B), ignoring all friction losses. Patin Note: If you find it necessary to solve the problem, you can make assumptions. But you must write down your assumptions. Take the gravity as g- 9.806 m/s² Hint: You can start with using Bernoulli Equation for A and C points.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

liquid pentane with relative density 0.62, 20 °c as shown in the figure at temperature, the geyç pressure is 0.2 atm dollars a cast iron (0.2 m odiameter cast iron)) it flows through the pipe.Marked as full pipe output it can be considered as the principal atmospheric pressure at the point at which it is. The total pipe length in the system is 45 m.5 kW in the system there is a pump that works with 92% efficiency in its power. Liquid since the volumetric flow rate of pentane is 0.05 m2 / s, with the tank calculate the height difference botween the pipe output. Data: * Friction loss at the pump is negligible. Gryc Atark purmp
The pressure of a reactor vessel can be adjusted bychanging either the inlet or outlet gaseous flow rate. Theoutlet flow is kept fixed as long as the tank pressure remainsbetween 100 and 120 psi, and pressure changes are treatedby manipulating the inlet flow control valve. However, if thepressure goes higher than these limits, the exit gas flow isthen changed. Finally, if the pressure exceeds 200 psi, a ventvalve on the vessel is opened and transfers the gas to a storagevessel. Design a control scheme that meets the performanceobjectives. Draw a process instrumentation diagram for theresulting control system
Centimuity oquation ofastendy frow. Terriellis problemfontflow of liquid througha hole) Problem:Detemine the absolute pressure at the inlet section of the pump. Flow rate of the pump Q=2,3 1/sec, l=1,5 m, d=40 mm, t=60°C. Static pressure in the tank p.=266,8 mmHg. Wedge resistance coefficient Sw=1,5, pipe inlet resistance coefficient Çin=0,5, the height of the oil level in the tank above the pump inlet section н-1,2 м, оil 1-12. H кран насос
3. A centrifugal pump of 350 mm diameter running at 1000 r.p.m. devclops a hcad of 18 metres. The vanes are curved back at an angle of 30° to the langent at outlet. If the velocity of flow is constant at 2-4 m/s, find the manometric efficiency of the pump. (Ans. 76-4%)
A centrifugal pump has an impeller of diameter 250 mm whose width at the exit is 50 mm. The flow velocity through the impeller having radial vanes is constant at 3.0 m/s. The speed of the pump is 1200 rpm and manometric efficiency is 85%. Find discharge (litres/ s) 18:21 /
For the hydraulic system of Figure, the following data are given: The pump is adding2.984kW to the fluid.(a) Pump flow is 0.00158 m3. (b) The pipe inside diameter is 0.01905m.(c) The specific gravity of the oil is 0.9.(d) The oil tank is vented to the atmosphere.(e) The head loss HL between station 1 and 2 is 12.19m.(f) The elevation difference between stations 1 and 2 is 6.096m.Find the pressure available at the inlet to the hydraulic motor(station 2).
times A cenrifugal pump having outer diameter equal two the inner diameter and running at 1200rpm works agaist a total head of 32m. The velocity of flow through the impeller is constant and equal to 3m/s. The vanes are set back at an anhgle of 30°at the outlet. If the outer diameter of the impeller is 600mm and width at outlet is 50mm, determine: a- Vane angle at inlet. b- Work done per second by impeller. c- Manometric efficiency.
Q1/ liquid is pumped from a ground level reservoir to an overhead tank through a 5 cm ID pipe as shown in Fig. (1): i. What pressure developed by the pump to 45° elbow 8 m Fig. (1) Globe valve Tank 5 m supply water to the tank at the rate of 245 I/min? ii. What is the power required for the pump, if the pump is only 62% efficient? iii. Calculate the available NPSH. If the pump required 12 m NPSH is it suitable to prevent cavitation for this system? why? Given that: u = 0.0016 Pa.s; p 850 kg/m', e/d 0.0035, (Le/d) of Globe valve (open) = 240 (Le/d) of 45° ēlbow = 24 and Pv = 36.6 kPa 25 m 45° Reservoir 45° elbow
A centrifugal pump having an impeller of diameter 500 mm delivers 140 litres of water per sccond. The velocity of flow is 1 m/s and the vanes are curved back at outlet at 30° to the wheel tangent. If the impeller speed is 400 r.p.m., find the power to drive the pump. (Ans. 12-9 kW) 3.
Consider a desired pump operating condition which adds 35 psi at a flow rate of 500 gpa to water. Ignore any changes in Kinetic or potential energy and assume isothermal flow (ie. Internal energy is constant, this is normal assumption we make when analyzing fluid flows in piping systems). Apply the energy balance only across the pump starting with full energy balance and simplifying to solve for the pump head symbolically. Then begin careful of unit, solve for pump head in feet. Given erosion 500 gpm P=62 lbs/ft^3 A- 10.5 ft B- 100.8 ft C- 50.1 ft D-80.7 ft
Q3: Two tank are connected with piping system as shown. If the pump characteristics are given by: hp- 31-120000 and, 7p--190000Q+8590Q Where hp is in meters and Q in m³/s and np is the pump efficiency (%).Estimate the operational cost of the pumping (10000) m² of water to the upper tank if the cost of IKwh is 2000 ID. Neglecting the minor losses. H=15mm 0-150mm
Head, m Consider the plot below, what is the operating flow rate of the pump in this ?system 25 20 15 10 5 0 0.01 0.015 1 0.02 0.025 Q, m³/sec 0.03 - -H-Q curve 0.035 0.04 0.02 m3/s O 0.026 m3/s O 0.32 m3/s O 0.035 m3/s O