Original Schematic and OrCAD Schematic: The input primary voltage is 250V, frequency 50 Hz, primary inductance setting is 2000H and secondary inductance is 10H and voltage peak to peak ripple is approximately equal to 92mv. Ut IN gOur DIND02 DINO02 C3 Rt TXI BC54SA VOFF =0 VAMPL FREQ 50 AC0 XFRM_LINICT-SEC 02 D5 BCS4SA DIN4002 + C2 0.384m

Original Schematic and OrCAD Schematic: The input primary voltage is 250V, frequency 50 Hz, primary inductance setting is 2000H and secondary inductance is 10H and voltage peak to peak ripple is approximately equal to 92mv. Ut IN gOur DIND02 DINO02 C3 Rt TXI BC54SA VOFF =0 VAMPL FREQ 50 AC0 XFRM_LINICT-SEC 02 D5 BCS4SA DIN4002 + C2 0.384m

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

REC United Peint 4OMO WODOA4 Outine- 000000- . PAnA Color color Edit Tooh Shapes Colors Calculate the temperature and static dynamic temperature of a p-n junction germanium diode if diode current is 2.72 mA and reverse saturation current is 1mA when a forward bias of 0.2V is applied.[K = 1.38 x 10-23JK-) %3D 1.6x1019
this is electric circuit questin ...plz solve it early .plz solve early
ffasssttt plz
PROBLEM: The diode (blue line) should be at -10V not -8V SOFTWARE USED: LTspice XVII---Figure 1 is my work, and figure 2 is the correct sample. Please tell me what I did wrong. Thank you :))---Below is the .asc filehttps://www.mediafire.com/file/zxauoh86zi79nfu/EXPERIMENT_01.asc/file
Using a positive Clamper Circuit, with an AC voltage of Vi = 13v with a frequency of 60hz, a value of 100u for the Capacitor, a silicon diode and a resistor with the value of 1000 ohms. Find the voltage value on the resistor at a simulation of 20ms. 2Vm Vm Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
The output for the following clamping circuit is shown below assuming ideal diode calculate the avarege value and r.m.s value for the output circuit Vm-10. V-5 (V+ V) V. RL (d) Figure 7-1 simple series clippers (Ideal diodes)
Using a positive Clamper Circuit, with an AC voltage of Vi = 100v with a frequency of 30hz, a value of 1000u for the Capacitor, a silicon diode and a resistor with the value of 100 ohms. Find the voltage value on the resistor at a simulation of Oms. Vm 2Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit
Parallel clipper circuit is given in the figure. Input voltage , Vs= 10 V. Find the voltages obtained on R1, RL and diode. (Note: Take the voltage amplitude as +10, -10V. Take the division value per oscilloscope screen as 5 ms. You can get the function generator frequency value as 50 or 100 Hz.) R-200 20 R |2 2K0 201
Q5) The schematic circuit in PLECS for a single-phase rectifier is shown below, Q5) The schematic circuit in PLECS for a single-phase rectifier is shown below, Thyristor Crout Probe Pulse Generator VC, pulses Probe Scope Thy Orso v Joad O R: 1 The output voltage across R is depicted in 0.5 0.0- b) 0.2 0.0 d)
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
Sample Problem. Determine the output waveform for the network below and calculate the output dc level and the required PIV of each diode. Assume supply of 100Vac,D2 and D3 are germanium diode, D1 and D4 are silicon diode and 1:2 center-tapped transformer. 120Hz www 1k
maysons rule and reduction block diagram