OP N C What is the shear resistance of a universal beam (UB) with the following dimensions [EC3 Section 6.2 Resistance of cross sections]: Cross sectional area A = 105 cm² Height h = 584.6 mm Flange thickness t = 11.4 mm Flange width b = 213.2 mm y-y Web thickness tw = 7.8 mm Root radius r = 12.7 mm Yield strength fy = 355 N/mm² Calculate the shear resistance and give your answer to the nearest whole kN. Do not include units in your answer.

OP N C What is the shear resistance of a universal beam (UB) with the following dimensions [EC3 Section 6.2 Resistance of cross sections]: Cross sectional area A = 105 cm² Height h = 584.6 mm Flange thickness t = 11.4 mm Flange width b = 213.2 mm y-y Web thickness tw = 7.8 mm Root radius r = 12.7 mm Yield strength fy = 355 N/mm² Calculate the shear resistance and give your answer to the nearest whole kN. Do not include units in your answer.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Date: Course: Time: Pind the vertical movement os is 120 KN Stsel Aluminum 3 m Im B P=120 kat Aluminum A = 900 mm² E = 70 GN m² steel A= 600 mm E 200 GNM² %3D
2.3-7 A steel bar 2.4 m long has a circular cross section of diameter d, = 20 mm over one-half of its length and diam- eter d, = 12 mm over the other half (see figure part a). The modulus of elasticity is E = 205 GPa. (a) How much will the bar elongate under a tensile %3D %3D load P = 22 kN?
Find the lightest S-shape for the beam shown if the working stress in bending is 175 MPa. What is the maximum bending stress in the beam selected? 50 kN/m 4 m -2.4 m· -x X- TABLE B-3 Properties of I-Beam Sections (S-Shapes): SI Units Flange Axis Y-Y Web X-X spxy Mass Area Width ıdə (wu) Thickness thickness Pl1 = S (10³ mm³) yli^ = 4 (10° mm*) (u) 27.7 27.7 22.1 Designation (10° mm*) (ww) 20.3 (ww) 38.9 („ww) (ww) (ww) 081 158 006 77 622 622 204 1 320 1 220 081 x 019S 4 230 240 34.5 338 × 158 x 149 x 134 007 184 15.7 3930 3 260 247 O'ZE 19.7 320 001 07 6'6E 32.3 006 81 00 I 15 200 149 6'81 15.9 166 937 677 234 019 215 134 181 22.1 090 € 2870 019 18.6 205 33.0 611 22.1 12.7 874 241 17.5 197 61I x 34.0 019 S510 × 143 143 18 200 16300 14 200 12 500 91S 91S 183 23.4 23.4 20.2 20.3 16.8 S69 653 2 700 20.8 228 x 128 x 112 × 98.2 128 112 33.8 34.5 29.5 179 961 2 540 007 194 19.4 80s 508 216 152 162 16.1 533 001 7 1950 12.3 98.2 20.2 12.8 495 6SI 11.4 144 30.2 661 S460 × 104 104 13 200 457 6SI…
The cross-sectional area of an aluminum bar is 170 mm?. It carries an axial loads at the positions as shown in the figure. Compute the total deformation of the bar if E = 80 Gpa. Assume the bar is suitably braced to prevent buckling. Add "9" in the loads only. Example: 40+9=49, 18+9=27, 42+9=51, 20+9=29 Area = 170mm' 2 40KN 18KN 20KN 42KN 1.0m 1.80m 0.70m
Q2/ Find (x) so that the rigid beam remains in a horizontal position. Aluminum L = 5m A = 400mm² E = 70GPA Steel L = 3m A = 500mm? E = 200GPA 5m %3D Rigid beam Answer: x = 0.719m P = 50kN
Civil Engineering Calculate the web in-plane bending buckling strength of a panel rib for: web thickness tw = 2mm web height bw = 40 mm effective modulus E = 8,044 N/mm2 %3D effective Poisson's ratio v = 0.25 in-plane bending buckling constant kb = 24 for all edges simply supported %3D Reduce the buckling constant by a factor of 10 for free edges Quote the value in MPa to one decimal place.
An aluminum strut has a cross section referred to as 30 mm 30 mm a deep hat. Locate the centroid ỹ of its area. Each segment has a thickness of 10 mm. 100 mm 80 mm
The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point P (very close to the bottom of the flange) is 12 MPa. The stress at point Q In the web (very close to the flange) is: N'-. 100- P Q 201 100- T 20 81484 80 20 40 --N (a) Indeterminable due to incomplete data (6) 60 MPa (c) 18 MPa (d) 12 MPa 068
The beam is made from a material that can safely support a tensile or compressive stress of 350 MPa. a) Based on this criterion, determine the largest force, F, the beam will safely support if it has the cross- section (a). b) What is the largest allowable F for cross-section (b) Recall for a rectangle: I = bh³/12 1.0 m- 60 mm 23.3 mm Figure 1 Cross-section (a) -0.63- 10 mm 10 mm 40 mm 10 mm -50 mm - Figure 2 Cross-section (b)
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee A w24 X55 is used as a beam with a length of 6m. The beam is supported by a bearing plate of 300 mm x 200 mm x 30 mm on the wall having a thickness of 250 mm.Properties: d=598.68mmbf = 177.93 mmtw =10.03mm k=33.34 mmtf = 12.83mmFy = 250 MPaQuestions:1. Determine the design strength for web local yielding.2. Determine the design strength for web crippling.
Q1: Define all the symbols of the scheme below. h b Ac A₂ 000 Section Neutral axis Ecu3 Strain
PROBLEMS: 1. The bolt connection shows 8-22mm diameter bolts in a bolt hole diameter of 25 mm and spaced according to the following: Sı = 40mm T = 16mm S2 = 80mm S3 = 50mm S4 = 100mm te = 12mm Determine the force T if the allowable tensile stress is 200 MPa, the allowable bolt shear stress is 120MPa and the allowable plate bearing stress is 120 MPa. 2. A long retaining wall is braced by wood shores set at ang angle of 30° and supported by concrete thrust blocks as shown. The shores are evenly spaced, 3m apart. For analysis purposes, the wall and shores are idealized on the second image. Note that the base of the wall and both ends of the shores are assumed to be pinned. The pressure of the soil against the wall I assumed to be triangularly distributed, and the resultant force acting on a 3-meter length of the wall is F= 190KN. If each shore has a 150mmx150mm square cross section, what is the compressive stress in the shores? Retaining wall Soil Concrete Shore thrust block 30 30 1,5 m…