A floor system consists of a 80mm concrete slab supported by continuous T beams with a span 7.3 m span, 1.2 m on centers. Web dimensions, as determined by negative moment requirements at the supports, are bw = 280 mm and d= 500 mm.

A floor system consists of a 80mm concrete slab supported by continuous T beams with a span 7.3 m span, 1.2 m on centers. Web dimensions, as determined by negative moment requirements at the supports, are bw = 280 mm and d= 500 mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. Determine the maximum flexural stress on the beam in MPa. Determine the maximum shearing stress on the beam in MPa.
A rectangular beam 350 mm wide is to be designed for an ultimate moment of 750 kNm with f'c = 28 MPa and fy = 415 MPa. The effective depth of the tension bars is 500 mm and 70 mm for compression bars. %D 1. Determine the depth of the stress block if the tensile strain is 0.005 when the concrete crushes at a strain of 0.003. (in mm) (one decimal place) 2. Determine the total amount of tension reinforcement for the given condition above. (in sq.mm) (whole number) 3. Determine the amount of compression reinforcement required. (in sq. mm) (whole number)
Determine the required steel area for a T-beam that traverses the center of a floor system for which bw = 300 mm and d = 550 mm. The beams are 4.8 m long and spaced at 3 m. O.C. The slab thickness is 100 mm. Mp = 400 KN-m (including its own weight), ML = 500 KN-m. f'c = 28 MPa, and fy = 414 MPa
What is the value of the force in column C5 and C6 in the ground floor (in kips to one decimal place)?
A 500mm width square tied column with reinforcement on four faces has a gross steel ratio is 0.02 and the concrete cover from the column surface to the steel centroid is 100 mm. What is the nominal axial capacity of the column if subjected to biaxial bending where ex = ey = 250 mm.? Use fc’ = 21 MPa and fy = 415 MPa, reciprocal load method, and the appropriate interaction diagram
A composite beam is fabricated by bolting two 3.6-in.-wide by 13-in.-deep timber planks to the sides of a 0.5-in. by 13-in. steel plate. The moduli of elasticity of the timber and the steel are 1700 ksi and 29000 ksi, respectively. The simply supported beam spans a distance of 25 ft and carries two concentrated loads P, which are applied as shown. Assume LAB = LCD = 7 ft, LBc = 11 ft, b = 3.6 in., d = 13 in. and t = 0.5 in. (a) Determine the maximum bending stresses o,,o, produced in the timber planks and the steel plate if P = 3.7 kips. (b) Assume that the allowable bending stresses of the timber and the steel are 1010 psi and 26800 psi, respectively. Determine the largest acceptable magnitude for concentrated loads P. (You may neglect the weight of the beam in your calculations.) Answers: LAB (a) o, = (b) P = i i B LBC b F لالها b Cross section C kips. d ksi, o, = LCD D ksi.
Situation. A flooring system consists of parallel I-beam sections spaced at 3 m. on centers simply supported over a span of 9 m. The beam supports a 200 mm thick concrete slab of ultimate strength f'c = 21 MPa. The flooring system is designed for as ceiling and floor load of 750 N/m². The properties of the I-beam sections are: A = 11,500 mm² d = 350 mm; tw = 10 mm bf = 250 mm; t = 16 mm lx = 266x106 mm4 ly = 45 x 106 mm4 fy = 248 MPal Wb = 90 kg/m fy = 248MPa If each beam is laterally braced by the concrete slab, calculate the allowable bending strength using safety factor of 1.67. Select the correct response: 175.17 248.79 235.94 394.03
1. The section of a reinforced concrete T-beam has d = 400mm, bf = 800mm, t = 100mm, bw = 300mm. The beam is reinforced with 8 pcs of 32mm rebars with Fy = 415MPA concrete has F'c = 28MPA. Determine the safe ultimate moment capacity of the beam.
A floor slab 100 mm thick is cast monolithically with beams 250 mm wide 450 mm deep spaced 1.2 m on centers, on simple supports over a span of 5.0 m. The floor supports a service live load of 2.1 kPa. Using f.-21 MPa, rebar strength f, 415 MPa, calculate the following if a typical interior beam is reinforced with 3- 16-mm-dia. flexure bars at the bottom enclosed with 10-mm-dia. stirrups: 1. Nominal moment capacity (kN-m) of a typical interior beam in positive bending considering T-beam geometry. A. 96.66 C. 91.10 Maximum factored uniformly distributed load (kN/m) a typical interior B. 86.99 D. 81.99 2. beam can sustain against positive bending. В. 27.83 с. 26.23 D. 29.15 A. 30.93 3. Maximum service superimposed dead load in kPa. A. 17.73 C. 16.52 B. 11.08 D. 14.77
1.) A beam carries the loading shown. Design a rectangular timber beam if the permissible stresses are 120 Mpa in tension and compression, and 100 Mpa in shear. 20 kN/m 50 kN A B 6 m + 2m
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. 2. Determine the moment of inertia, I, of the section in mm^4.
Uniform concrete slab has a mass of 2400 kg. Determine the tension in each of the three parallel supporting cables when the slab is held in the horizontal plane as shown.