One hole will be formed on plate sheet with ultimate shear stress = 1.5 kN/mm2. If compression stress on drill blade limited to 600 N/mm2, calculate the maximum depth on plate, t in order to make 700mm diameter hole.

Q: Please provide a clear step-by-step solution. Thank you!   A firm shaft with radius R has a…

A:

Q: Given data: Maximum shear stress-50 MPa Maximum principal stress=80 MPa Find minimum principal…

A:

Q: Figure shows that a hole must be drilled in a plate with a shear strength of 40 ksi. Compressive…

A:

Q: n problem 3.52, consider the following. Do not change the distance between A and B, and B and…

A: Hi, we will solve first part for you since the other sub-parts are complex. Please resubmit the…

Q: A Drive Shaft for a milling machine transmits 30 horsepower at a speed of 500 RPM. Compute the…

A: A Drive Shaft for a milling machine transmits P = 30 horsepower = 30 × 746 Watts, at a speed of N =…

Q: A 40-mm diameter hole is drilled 3-m deep into the steel shaft. When the first torque is removed at…

A: Let shear modulus (G) of steel shaft be 83 GPa. The torque in AB and BC portion is -TAB=6000-2000 =…

Q: The five-bolt connection shown in the figure must support an applied load of P = 295 kN. If the…

A:

Q: ort square is 1 1/2 inches x 1 1/2 inches in cross section. it is on an axial tensile load of 11,000…

A:

Q: A drilling machine is capable of drilling 30 holes of 20mm diameter per minute in a 16mm thick steel…

A: please refer handwritten solution

Q: D. For a circular section the ratio of maximum shear stress to the average shear stress is

A:

Q: To build a Tesla car, a machine incorporated with a special tube having a 4mm wall, as shown below,…

A: Given: To find: Average shear stress at A and B

Q: A pipe has an outside diameter of 0.7 inches and inside diameter of 0.12 inches. A force of 144 lbs…

A:

Q: shop plans to subject the said shaft on a loading condition as shown in the figure. If the shearing…

A:

Q: A cylindrical steel pressure vessel 400 mm in diameter with a subjected to an internal pressure of…

A: Givendia=400mmthickness t=20mmInternal pressure P=4.5MN/m2

Q: A section of the beam is subjected to combined tensile stress of 150 MPa tensile stress of 60 MPa…

A:

Q: Calculate diameter of shaft using maximum shear stress theory,when equivalent torque of 1000 x 103…

A: Given           Equivalent torque, T = 1000 x 103 N-mm  The allowable shear stress = 60 Mpa Find…

Q: A sleeve made of AISI 1040 CD steel has inner and outer diameters 40mm and 50mm, respectively. press…

A:

Q: A propeller shaft is required to transmit 45 kW power at 500 r.p.m. It is a hollow shaft, having…

A: Given data: -  The power transmitted by the shaft is P = 45 kW. The speed of the shaft is N = 500…

Q: One hole will be formed on plate sheet with ultimate shear stress = 1.5 kN/mm2. If compression…

A: According to question given data Hole diameter = 700 mm Compression stress = 600 N/mm2 Ultimate…

Q: For the direct shear example shown below, if F = 47 kN, AAB = AcD = 3151 mm², the average shear…

A: Given:Force acting, F=47 kNArea of the surface, AAB=ACD=3151 mm2

Q: A bolt assembly is experiencing 100 kN of force. The diameter of the head is 50mm, bolt diameter is…

A:

Q: Find the torsional shear stress on a 2 inch diameter shaft if it is subjected to a torque of 561…

A: Given diameter of shaft = 2 inch. Torque=561in-lb.

Q: A pipe has an outside diameter of 0.8 inches and inside diameter of 0.19 inches. A force of 105 lbs…

A: Given     Outside diameter, d2 = 0.8 in        Inside diameter, d2 = 0.19 in…

Q: The 2.3-in.-diameter drive shaft AB on the helicopter in (Figure 1) is subjected to an axial tension…

A: Given data:- Diameter of the shaft =2.3-in. Axial tension (P)=10000 lb torque (T) =345 lb⋅ft To…

Q: During drawing process, using the Ao=5mm2, Af =4 mm2, K=200 MPa and n = 0.20, the average flow…

A:

Q: Can you explain this part please? How you got 412.72? Stress = force/area Stress = 4849…

A: Actually it is not 412.72, its cross-sectional area of cylindrical polymer i.e. A=π4×d2A=π4×12.72…

Q: A cylindrical pressure vessel has an outside diameter of 1.5 meters, and a length of 5 meters. The…

A: The outside diameter of a cylindrical pressure vessel is 1.5 metres and its length is 5 metres. The…

Q: Given data : Maximum principal stress=100 Mpa Minimum principal stress=-50 MPa Determine maximum…

A:

Q: WITH DESCRIPTION AND STEPS APPLIED, TO HELP ME UNDERSTAND APPROPRIATELY

A: Hoop stressExplanation:Step 1:Step 2: Step 3: Step 4:

Q: The motor in the figure is transmits movement to the flywheel. The power of the engine is 4 kW and…

A:

Q: A flanged bolt coupling is used to connect a solid shaft 120 mm in diameter to a hollow shaft 100 mm…

A:

Q: 3. Find the proper thickness of 900 mm cast-iron pipe under a 95m head of water with a working…

A:

Q: A press is used to punch 10 holes per minute of 30 mm diameter hole from 25 mm thick plate.…

A:

Q: A square hollow bar has a breadth and depth of 30mm and a wall thickness of 2mm. A tensile force of…

A: An object deforms when a deforming force is applied to it. An opposing force will be generated…

Q: A solid steel shaft is to transmit 100 HP at a speed of 1,000 rpm. The allowable shear stress is…

A: Given, Power(P) = 100 HP P = 100 × 550  ft.lb/s = 55000 ft.lb/s Speed(N) = 1000 rpm N = 1000 × 2π60…

Q: Question 2 60 nim Circular fillet with radius of 15 mm The built-up shaft is to be designed to…

A:

Q: For the figure shown below. Calculate the increase in vertical stresses (Ac) at point A at depth of…

A:

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.