Pleasr don't provide handwritten solution .... Often, the properties of multiphase alloysmay be approximated by the relationshipE (alloy) = EaVa + EBVBwhere E represents a specific property(modulus of elasticity, hardness, etc.) and Vis the volume fraction. The subscripts a andB denote the existing phases ormicroconstituents. Employ the relationshipabove to determine the approximate Brinellhardness of a 99.78 wt% Fe-0.22 wt% Calloy. Assume Brinell hardnesses of 80 and280 for ferrite and pearlite, respectively,and that volume fractions may beapproximated by mass fractions.See Animated Figure 10.28(10.24)i

Answered: Image /qna-images/answer/587c1b19-4b32-48ef-b683-4f01d49d8e41.jpg

Answered: Often, the properties of multiphase…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

According to Reference [1], alloys of nickel (Ni) and tungsten (W) are can form substitutional solid solutions up to approximately 11 at% W. Consider two different alloy compositions: Ni-5W (5 at% W) and Ni-10.5W (10.5 at% W). A. Which composition should be more ductile? B. Which composition should be stronger? C. Using the oy~ C¹/2 relationship from the lecture slides, how many times larger should the yield strength be for Ni-10.5W compared to Ni-5W? D. Where should the tungsten atoms sit relative to the dislocation on or opposite the side with the extra half-plane? You will need information from Appendixes of the textbook.
What is the composition, in at. %, of an alloy that contains 35g of Cu and 42g of Zn Acu= 63.55g/molAzn=65.41g/mol
The TTT diagram for a 1076 eutectoid steel is given: What is the heat treatment process to form 50% Coarse Pearlite + 50% Martensite. 800 A 1400 Eutectoid temperature 700 A 1200 600 1000 500 800 400 A 600 300 M(start) 200 50% 400 M + A M(50%) M(90%) 100 200 10-1 1 10 102 103 104 105 Time (s) Temperature (°C) Temperature (°F)
The Sheady Ceap data of stainless cheel tkon at Stress level Fompa ů qiven in te Table Compute he steady-ctate Cleep dets for this alloy at 1a5ok and Shee level of 5omPaf Hhe shees erpinen t fox the alloy ū 7.0. fempersiuse 977 1089 2.0X 183
QI/ Draw a thermal equilibrium diagram for the binary alloy system (Si –Au), from the following data:- a- Si melts at 1414 °C, and Au melts at 1064 °C , and identify all phases are present in the diagram. b- Eutectic is formed at 360°C containing 20 Wt% Si -80 Wt% Au . c- Determine the amount of each phase for the alloy which consist 60 Wt% Si- 40Wt % Au at 1200 °C and 800 °C ,then determine the amount of eutectic at 200 °C?
The TTT diagram for a 1077 eutectoid steel is given. Explain the heat treatment process to form 50% Fine Pearlite + 50% Coarse Bainite. 800 A 1400 Eutectoid temperature 700 A 1200 600 1000 500 B 800 400 A 300 600 M(start) 200 M + A 50% 400 M(50%) М190%) 100 200 10-1 1 10 102 103 104 105 Time (s) Temperature (°C) Temperature (°F)
For 40 wt% Sn – 60 wt% Pb alloy at 150 oC (at point B) as shown in Figure, i. State the name of phase(s) present. ii. Calculate the composition(s) of the phase(s) present. 600 300 Liquid 500 a+L 200 400 300 100 200 100 20 60 100 (Pb) (Sn) Composition (wt % Sn) Temperature ("C) Temperature ("F)
800 A Eutectoid temperature H 1400 700 A H 1200 600 1000 500 B 800 400 A 300 600 M(start) 200 M + A 50% 400 M(50%) M(90%) 100 200 10-1 1 10 102 103 104 105 Time (s) Using the isothermal transformation diagram for an iron-carbon alloy of eutectoid composition, specify the final microstructure and approximate amount of each. Assume a small specimen has been held long enough to have achieved a complete and homogeneous austenitic structure prior to treatment. Sample (1): Quickly cool specimen from 800°C to 575°C, hold for 10 s, then quench to room temperature. Sample (2): Quickly cool specimen from 800°C to 500°C, hold for 100 s, then quench to room temperature. O after treatment, sample 1 is 50% pearlite, 50% austenite O after treatment, sample 2 is bauxite O after treatment, sample 1 is 25% pearlite O after treatment, sample 2 is bainite O after treatment, sample 2 is austenite O None of the answers is correct. O after treatment, sample 2 is coarse pearlite O after treatment, sample 1 is…
Q1 / Two metals Beryllium (Be) and Silicon (Si) have melting points 1282°C and 1414 °C respectively, are completely soluble as liquids but completely insoluble as solids . They form a eutectic at 1090°C containing 61 wt% Si -39wt% Be? Determine the following:- 1- Draw the thermal equilibrium phase diagram and identify all phases are present in diagram ,then sketches what happens in microstructure when the alloys containing , a- 10wt% Si, b-70wt%Si , solidify completely. 2- Determine the composition and the amount of each phase for the alloy which contain 15 wt% Si-85wt% Be at 1150°C If the alloy is hypoeutectic determine the amount of eutectic at 600 °C? or hypereutectic and
For a Fe-C alloy with a eutectoid composition, an austenite was rapidly cooled down to 450°C, held for 10 sec, and quenched to room temperature. What is the final microstructure based on its TTT curve? Amount Temperature of Transformation, C 700 600 500 400 300 200 Ae₂! Ae₁ Austenite unstable Ms. 10 10² 103 104 105 seconds Austenite stable 50%- 100 MF TELEP P 100% completed F+B Coarse Pearlite - Fine Pearlite -Upper Bainite (Feathery) Lower Bainite → Martensite + Bainite Martensite 1 1sec 1 min 1hr Transformation Time (Log. Scale) O a. 50% bainite and 50% martensite O b. 50% austenite and 50% bainite O c. 100% bainite O d. 100% martensite Finer Lamellac Bainitic Pearlitic Austenite Fine more Acicular Rapid Etching Martensitic cicular, Slow Etching V.P.H. 210 320 450 700 750
Figure 1 show Eutectoid Plain Carbon Steel Phase Diagram. Please indicate the phases present and their corresponding weight fraction at points a, b, c and d. Show your tie-line and calculations based on Lever Rules. Temperature (°C) 1100 900 700 500 300 100 0 100% Fe 7 0.02 1.0 Fe,C 1.2 2.0 7 7 7 7 Fe, C Figure 1 Fe,C Pearlite 4.0 3.0 Weight percent carbon 7+ Fe, C 727°C a + Fe₂C 5.0 Fe, C 6.0 6.7
Q) Consider a 1.5 kg of a 99.7wt% Fe-0.3 wt% C alloy thatis cooled to a temperaturejust below the eutectoid.(a) How many kilograms of proeutectoid ferrite?(b) How many kilogram of cementite form ?(c) How many kilograms of all ferrite form? And How many kilograms of cutectoid ferrite?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS