Directions: Draw an isometric view of the following orthographic views. Views most be properly aligned attached. Use the grid lines to define the size S

Q: Given the top and front view create a section view.

A: Find Create a section view using the given top and front views.

Q: 12-x2 了了少 Je

A:

Q: L-20 inches d-0.75 inch a-0.1875 inch Ea-10,000 ki Eb-17,000 ki Pa-Pb What is the thickness b?…

A:

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: Consider a virtual load Q, acting vertically downwards, is applied at point A.Draw the given truss…

Q: 01/ Give the dimensions for the hole and shaft for the 12 mm electric motor sleeve bearing (pump);

A: Given:Basic size given for motor sleeve bearing=12 mm

Q: I o2s+lo4 s+1. .96 2. L'st ++T?

A:

Q: Draw chalk diagram of all sections

A: To draw section views

Q: The steel box wrench (E=29,000ksi, v=0.32) is loaded with a 40-lb horizontal force and a 25-lb…

A:

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: A mass of 25 lb is applied at the end of a 2-inch-diameter rod shown in Figure P2. If the modulus of…

A:

Q: Determine ly and ky.

A:

Q: A 70 kg skier that moves from rest at A is shown in Figure Q2. Suppose friction can be neglected…

A: Given:m=70 kgθ=30°θ=40°Height AB=12mTo find:-1) Velocity VB2) The istance S

Q: The engine piston weighs 180 g. The machine speed is 4400 RPM. What is the maximum speed of the…

A:

Q: A force F = 6980 N acts upon a piston head, as shown in the figure. The gudgeon pin G connects the…

A:

Q: Q3/ Determine the resultant of the force system with respect to the point (A)

A:

Q: How many balls of 50 mm diameter fit in a volume of 1910 L

A: Given:-Diameter of ball (d) = 50 mmVolume of container (V) = 1910 literTo Find :-Number of such…

Q: Consider the crank assembly of the figure. The bearings at points A and B are in good alignm…

A:

Q: During the governor regular working time the sleeve moves up with 16mm due to the effort of 225N…

A: Given that, The effort of the governer, F=225 N and the movement of the sleeve is, x=16 mm=0.016 m,

Q: a) Calculate the area of the plate. A= Number in?

A: Given:

Q: Using unity conversion ratios, show that 1.00 lbm weighs 1.00 lbf on earth

A: Given Data: The given mass is M = 1 lbm. The expression for the weight (W) is, W=Mg Where g is the…

Q: Eind feslads osd Tarque Pressre ond N= mim Ponued 1500xpm

A: Mean effective Pressure is the ratio of work done in a cycle to the engine displacement That is,…

Q: Give a steps by steps answer of the solution

A:

Q: Round number to three significant figures. 0.000045389

A: Given data: The given number is N = 0.000045389. Here, there are a total of 5 significant figures.…

Q: Deleimine wasik done

A: Given data : The value of force applied=F The value of displacement=D   To find : Work done

Q: Express the quantity 30.6×10^−4m in mm

A:

Q: Where did you get the 3 from for the distance of q?

A:

Q: (5) In order to forge a pure gold ring, you first need to purchase the gold. The ring design is a…

A: According to Pappus–Guldinus theorem volume can be given as V=Ax2π×yArea of the block as per given…

Q: Make the indicated conversion between customary and metric units of weight and mass. 17…

A:

Q: D= 1.75 in d= 0.75 in r= .120 in

A: Calculate D/d and r/d ratio, Fr calculating the stress concentration factor we use the…

Q: 2x105 Nlmen2 Biomaha uemprog aoo un qans G ) Tatal anctansion the ban

A: Normal stress is defined as the intensity of force exerted on an area perpendicularly. Normal stress…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.