Note: All dimensions are in mm A 34 mm diameter x 120 mm shafting will be turned using a lathe to produce a step shafting as shown in the figure. Calculate the required (minimum) total machining time Tm with the following cutting 30 70 *- 50-> 120 conditions: Step Shafting Rough Turn: V = 30 m/min; Max. Depth of Cut = 1.5 mm; Feed = 0.2 mm/rev Finish Turn: V = 60 m/min; Max. Depth of Cut = 0.5 mm; Feed = 0.05 mm/rev Lathe available rpm: 150, 200, 250, 350, 400, 450, 500, 550, 600, 650, 700

Note: All dimensions are in mm A 34 mm diameter x 120 mm shafting will be turned using a lathe to produce a step shafting as shown in the figure. Calculate the required (minimum) total machining time Tm with the following cutting 30 70 *- 50-> 120 conditions: Step Shafting Rough Turn: V = 30 m/min; Max. Depth of Cut = 1.5 mm; Feed = 0.2 mm/rev Finish Turn: V = 60 m/min; Max. Depth of Cut = 0.5 mm; Feed = 0.05 mm/rev Lathe available rpm: 150, 200, 250, 350, 400, 450, 500, 550, 600, 650, 700

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please do Asap
Q6: A-List the characteristics of screw thread. B- Calculate the change gears for cutting 16 thread per inch on a lathe having a lead screw of 6 thread per inch?
Please don't provide handwritten solution...
Machining time required reduce a mild steel rod of diameter 60mm, initial length (L) 125mm to final length (L1) 120mm to 58 mm by turning a carbide insert. If the approach length and over run length are 5 mm and 1 mm respectively, take Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
Need accurate answer for this please
A NC lathe cuts two passes across a cylindrical workpiece under automatic cycle. The operator loads and unloads the machine. The starting diameter of the work is 3.00 in and its length = 10 in. The work cycle consists of the following steps (with element times given in parentheses where applicable): 1 - Operator loads part into machine, starts cycle (1.00 min); 2 - NC lathe positions tool for first pass (0.10 min); 3 - NC lathe turns first pass (time depends on cutting speed); 4 - NC lathe repositions tool for second pass (0.4 min); 5 - NC lathe turns second pass (time depends on cutting speed); and 6 - Operator unloads part and places in tote pan (1.00 min). In addition, the cutting tool must be periodically changed. This tool change time takes 1.00 min. The feed rate = 0.007 in/rev and the depth of cut for each pass = 0.100 in. The cost of the operator and machine = $39/hr and the tool cost = $2.00/cutting edge. The applicable Taylor tool life equation has parameters: n = 0.26 and…
How much machining time required to turn a mild steel rod from 65mm to 58 mm over a length of 100 mm by turning using a carbide insert. If the approach length and over run length is = 5 mm, Cutting speed is 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm D
D. = 0.250" D, = 0.125" L= 6.250'" If Cutting speed v=211 FPM (feet per minute) and f= 0.0018 in/rev; Find (d) d=? (e) MRR=?
6
Explain and Solve correct i got wrong answer Previous time