|d = 8.0 mm T L = 200 mm

Q: Q16/ The value of the normal stress due to :axial force 2 kN applied on the beam is Point D 10 kN…

A: For this question, Axial force = P = 2 kN = 2000 N Cross section of the beam = 200 mm x 100 mm    We…

Q: The solid compound shaft, made of three different materials, carries the two Torques shown. (a)…

A:

Q: To determine the shear stress in the following shaft at points A and B. The material is steel.…

A:

Q: A 45-mm-diameter solid steel shaft supports loads PA-1.2 kN and Pc-2.7 kN as shown. Assume that L₁ -…

A: The diameter of the solid shaft d =45 mmThe support loadThe length of the sectionAt point B is…

Q: 3.10 The stepped steel shaft carries the torque T. Determine the maximum allow- able magnitude of T…

A:

Q: The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the…

A: Given data: -  The torque at point A is TA = 2T. The torque at point B is TB = 3T. The allowable…

Q: Q3: The shaft consists of three concentric tubes, each made from the same material and having inner…

A: Handwriting.jpg

Q: d Bronze B Steel - b–

A:

Q: A muff coupling connects two shafts to transmit a torque of 135.6 N-m, the diameter of the shaft is…

A:

Q: I only need 5

A: Solution:

Q: The drive shaft of the motor is made of a material having an allowable shear stress of τallow= 72…

A:

Q: 3.13 The shaft consisting of steel and aluminum segments carries the torques T and 27. Find the…

A:

Q: shaft of 53 mm diameter is subjected to a bending moment of 1477158 N-mm and a torque T N-mm. If the…

A:

Q: Torsion A hollow circular shaft has inside and outside diameters of 30 mm and 40 mm respectively.…

A:

Q: 2. A tube is made of aluminum (G = 24 GPa ) and has a rectangular cross section as shown in figure.…

A:

Q: Circular solid ACB shaft is fixed supported between the wall at A and B. If the allowable shear…

A: Allowable shear stress τallowable=42 MPa=42×106 N/m2Let the maximum torque applied at section C be…

Q: flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and…

A: The diameter of bigger circle is The diameter of smaller circle is The number of bolts on bigger…

Q: A compound shaft consists of an outside tube (1) and an inner tube (2) that are fully connected…

A:

Q: A motor supplies 154 hp at 470 rpm to flange A of the shaft. Gear B transfers 74 hp of power to…

A:

Q: The solid shaft of radius r is subjected to a torque T. Determine the radius r of the inner core of…

A: given data as per the question The radius of the bar = r Torque subjected = T

Q: The compound shaft made from the same material consisting of two segments AC and CB is firmly…

A:

Q: 400 mm 400 mm 11th. Of the spindle in the figure AB the portion is full and BC part is empty. To the…

A: Given, Total applied Torque (T)= 8kNm Modulus of Rigidity (G)= 80GPA Solution Divide the spindle…

Q: Determine the size of the shaft,

A: Given: P=22 kW N=550 rpm shear stress=42 MPa Tensile/compressive stress=56 MPa P=900 N L=2.5 m To…

Q: Let's consider a solid circular shaft subjected to the torque loads as shown. Determine the minimum…

A:

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

A:

Q: The steel shaft shown in the figure is subjected to a torque of 190 lbf in applied at point A. Find…

A: The torque reactions, the angle of twist at A, and the shear stresses in the sections OA and AB.…

Q: Q4 An aluminium tube, 1.2 m long, has the semi-circular crossection shown in the fig. If the stress…

A: LA=Length of an Aluminum tube=1.2 mσS=Maximum shear stress=35 MPa=35×106 PaG=26 GPa=26×109…

Q: . Determine the torque applied.

A: Determine the torque applied.

Q: The diameter of and LCD = 240 mm. 1. The lengths LAB = LBC = 200 mm parts AB and CD of the bar is 25…

A: Find the angle of twist and torque .

Q: Missing value MT = M0 (kN.m) 170 Kindly write legibly. Thank you Solve for: a) Determine the shear…

A:

Q: 12 mm -450 mm-

A: For solution refer below images.

Q: A flanged bolt coupling consist of six 10 mm diameter steel bolts on a bolt circle 300 mm. in…

A:

Q: The solid-circular member AC, having a diameter D and a shear modulus of 69 GPa, is subjected to the…

A:

Q: The bearings at A and B exert only x and z components of force on the steel shaft. a) Draw shear,…

A:

Q: Lets consider a solid circuar shalt subjected to the torque loads as shown. Determine the minimum…

A:

Q: a solid rod with a circular cross-secton is subject to a torque of 253 N.m. if diameter of the rod…

A:

Q: The dimensions of the cross section of an airplane fuselage are shown in figure 1. If the fuselage…

A: Given Data: The torque subjected to the fuselage is, T=8 MN·m=8 MN·m×1000 mmm=8×103 MN·mm. The…

Q: A 1100 Nm torque is applied at B (CW looking from C towards A). Shaft (1) is solid brass with G 40…

A:

Q: A steel tube of outer diameter 86mm and inner diameter 52mm is under pure torsion. The diameter of a…

A: Outer diameter = 86 mm Inner diameter = 52 mm Answer is (B) 81.98 mm

Q: The shaft ABC shown in the figure is drivenby a motor that delivers 300 kW at a rotational speedof…

A: Given: The power, P = 300 kW The speed of shaft, N = 32 Hz The power at gear B, P1 = 120 kW The…

Q: T 100 mm 70 mm 70 mm y T

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.