mechanicaldesignA shank with mill scale of 400 mm length is supported freely at its two ends. Itis acted upon by central concentric cyclic load having a minimum value of 10 kNand a maximum value of 60 kN. Knowing that the factor of safety is 1.5 and the sizefactor is 0.85. The material properties depends upon your choice from the attachedTable A-21. After a while a second loading was added to the shank of cyclic torquethat varies from 300 N.m CW to 100 N.m CCW. Fine the percentage change in theshank diameter between the two loading cases.pls solve fast

Step 1:Sure, let's break down the solution step by step to clearly explain how we arrived at the…

Answered: mechanical design A shank with mill…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a bolted joint two members are connected with an axial tightening force of 2200 N. If the bolt used has metric threads of 4 mm pitch, the torque required for achieving the tightening force is
Q-3 A 25-mm-diameter solid round bar has a groove 2.5-mm deep with a 2.5-mm radius machined into it. The bar is made of AISI 1050 CD steel and is subjected to a purely reversing torque of 250 N-m. For the S-N curve of this material, let f= 0.9.
A M20 × C4 bolt of mild steel is having yield stress of 320 MPa and factor of safety 3. The safe static tensile load in kN will be
Situational Problem ( 3 - 4) An automobile engine develops 33.5 hp at 1,000 rpm. The clutch used to transmit this power in a single plate clutch with two pairs of contact surfaces. The coefficient of friction is 0.4 and the mean diameter of the disk is to be 190 mm. The average normal stress on the clutch lining is 120 kPa. 3. Determine the axial force to engage the clutch based on uniform wear. A. 1.57 kN B. 3.14 kN C. 5.28 kN D. 7.46 kN
An A-36 steel bolt (AB) is used to snugly clamp a 6061-T6 aluminum sleeve between two rigid platens E and F, as shown below. The bolt has a solid, circular cross section with a diameter d = 61 mm and a thread pitch of 1 mm. The sleeve has a hollow circular cross section with an outer diameter do 250 mm and a wall thickness tw = 15 mm. The nut is then tightened 34 of a turn, which induces stresses in both the bolt and the sleeve. Assume Es = 200 GPa for steel and Ea 68.9 GPa for aluminum. 450 mm F A -250 mm- 500 mm 15 mm (a) Determine the normal stress in the bolt (both magnitude and sign). (b) Determine the normal stress in the sleeve (both magnitude and sign).
In the figure below the clamping force on the pipe is (331.7 lb), knowing that a single threaded screw Acme with major diameter (1 in) is used with coefficient of friction (0.2135). If booth screw and nut are made from 1030 - hot rolled Carbon Steel. Determine: 1- The tightening and loosening torques. 2- Thread screw and nut shear safety factors in case of double threads are in engagement. 3.3 in 2 7.2 in 32 3 in hinge
The specifications for a coil spring are known. Infinite fatigue life is required, using a safety factor of 1.3 applied to the maximum load only. The fatigue strength can be represented by a line between τmax= 600, τmin= 0 and τmax= τmin= 900 MPa.Assume both end plates are in contact with nearly a full turn of wireand that the end plate loads coincide with the spring axis.Determine a suitable combination of d, D, and N, if C = 8
A link in a mechanism for an automated packag- ing machine is subjected to a direct tensile force of 1720 lb, repeated many times. The link is square, 0.40 in. on a side. Specify a suitable steel for the 3-3. link.
The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength (Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (Sf) is equal to 0.8 Su and endurance Strength (Se) is equal to 0,5 Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S-N diagram
(4) An electric motor purchased by your employer surprisingly arrived without a keyway in the shaft. The motor has power rating of 7.5kW & 1,800rpm & has a shaft of Ø17mm. It will be used to drive a centrifugal pump using cast iron sheave. Design the square key to be used in the assembly based on maximum bearing & shearing stresses of 580MPa & 370MPa, respectively, and factor of safety of 5.
. The mean diameter of the driving pulley for a vec-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of frietion between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm.
For the Problem-1, determine the critical load if its length is 700 mm

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS