Calculate ther and ecomponents of acceleration.Answers:The particle of mass m= 3.6 kg is attached to the light rigid rod of length L=0.71 m, andthe assembly rotates about a horizontal axis through Owith a conatant angularvelocity 8 = w =2.0 rad/a. Determine the force Tin the rod when 8 = 21". The force Tispositive if in tanaion, negative if in compression.

T+mgsinθ=mLω2T=mLω2-mgsinθT=3.60.71×22-9.81×sin21oT=-2.412Hence it is Compressive in nature

Answered: Cakculate ther and ecomponents of…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Apply the asymmetric bending theory to the cantilever beam shown below to determine:I. Main moments and inertias.II. The angle of the neutral axis respect the horizontal.III. If ???? = (table) ???, work out the maximum F force that can be applied.3L = (7.5) mb = (57) cmh = (47) cmθ = (56) ° mpa 30
Activity 1. A weight is suspended from the accelerating frame shown by two cords A and B. Determine the acceleration of the frame which will cause the tension in cord B to (Ans. a = 1.89 m/s?) be twice that in cord A. a A60° 60 B Frame
The two blocks used in a measuring device have negligible weight. The spring is compressed 4 in. when in the position shown. The end of the screw is smooth and the coefficient of static friction at all other points of contact isμ = 0.21. (Figure 1) Figure P k = 20 lb/in. B 45° A 60° < 1 of 1 Determine the smallest axial force P which the adjustment screw must exert on B in order to start the movement of B downward. Express your answer to three significant figures and include the appropriate units. P= Submit μA Value Provide Feedback Request Answer Units ?
The beam of negligible weight is supported horizontally by two springs. The beam is horizontal and the springs are unstretched when the load is removed. Suppose that k₁=1.5 kN/m and ka 2.6 kN/m (Egure 1) Figure 600 N/m 3 m 1 of 1 D Y Part A Determine the angle of tit of the beam when the load is applied Express your answer using three significant figures. Η ΑΣΦ 0= Submit Provide Feedback Request Answer vec 5 I
3. The resultant of the three forces shown is the force R= 200k N. Determine P1, P2, and P3. 120 mm 150 mim P3 150 mm 320 mm 200 mm A dreamstime
The two blocks used in a measuring device have negligible weight. The spring is compressed 4 in. when in the position shown. The end of the screw is smooth and the coefficient of static friction at all other points of contact is μ = 0.35. (Figure 1) Figure P k = 20 lb/in. B 45° A 60° 1 of 1 Part A Determine the smallest axial force P which the adjustment screw must exert on B in order to start the movement of B downward. Express your answer to three significant figures and include the appropriate units. P = Submit μA Value Provide Feedback Request Answer Units
N.cm Q1. The 1000 clockwise is the resultant of the force system shown in figure 1, determine the value of P,q and C. 0.5 q N/cm 19N/cm A N 30 100 N 75
Q1. The 1000 Nm clockwise is the resultant of the force system shown in figure 1, determine the value of P,q and C. 0.5 q Niem N/cm P A N 30 100 N 75
A cantilever beam is 4m long with a EI = 20MNm^2. It has a point load of P=1kN at the free end and a u.d.l of q = 300N/m along its entire length. what is the reaction at A? what is the moment at A? Calculate the following at the free end slope and deflection
1. Figure Q1 shows a simplified diagram of a Ram Air Turbine (RAT), where the force on the rotor is represented by the 2 kN load shown. a. Produce shear and moment diagrams for the supporting frame ABC. b. Calculate the horizontal deflection of the point of loading. Assume that frame ABC has bending stiffness El = 2.7×105 Nm². 0.9 m A 0.6 m C B 2 KN
The particle of mass m = 2.0 kg is attached to the light rigid rod of length L = 1.17 m, and the assembly rotates about a horizontal axis through O with a constant angular velocity θ˙ = ω = 2.0 rad/s. Determine the force T in the rod when θ = 20°. The force T is positive if in tension, negative if in compression.
The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E= 200,000MPa and a 11.7 Neglect bending of the beam. FF A=640mm2 A=320mm2 D 1.2m 0.8 m 1.2m V 54KN What is the vertical displacement of D when there is no change in temperature in mm?

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS