Q4/ The outlet pipe from a pump is a bend of 45° rising in the vertical plane as shown in Fig. 4. The bend is 150 mm diameter at its inlet and 300 mm diameter at its outlet. The pipe axis at the inlet is horizontal and at the outlet it is 1 m higher. By neglecting friction, calculate the force and its direction if the inlet pressure is 100 kN/m² and the flow of the water through the pipe is 0.3 m³/s. The volume of the pipe is 0.075 m³? P1 up A₁ Fig. 4 P2 u2 A2

Q4/ The outlet pipe from a pump is a bend of 45° rising in the vertical plane as shown in Fig. 4. The bend is 150 mm diameter at its inlet and 300 mm diameter at its outlet. The pipe axis at the inlet is horizontal and at the outlet it is 1 m higher. By neglecting friction, calculate the force and its direction if the inlet pressure is 100 kN/m² and the flow of the water through the pipe is 0.3 m³/s. The volume of the pipe is 0.075 m³? P1 up A₁ Fig. 4 P2 u2 A2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Figure shown below is a gate in the form of circular arc with a central angle of 60° and radius 2m with one end resting on the crest of the dam. The water surface is flushed with the upper end of the gate. Find the vertical component of hydrostatic force (kN) acting on the gate. The gate is 2.22 m long normal to the plane of the paper. O 2m 60 ° 2m
# 4] The isosceles triangle gate shown in the figure is hinged at A and weighs 1000N. What is the total hydrostatic force acting on one side of the gate in kiloNewton? Locate the center of pressure from B. -.Is... 3.0m 2m 3.0m 60 B.
Water flows at a rate of 0.5m³/sec round a 50° contracting pipe bend which lies in a horizontal plane. The diameter at the entrance is 700mm and at the exit 500mm as shown in figure below. If the pressure at the entrance is 200kPa, determine the magnitude and direction of the force exerted by the fluid on the bend. d = 500mm out d =700mm 2 in 50
Q4/ The outlet pipe from a pump is a bend of 45° rising in the vertical plane as shown in Fig. 4. The bend is 150 mm diameter at its inlet and 300 mm diameter at its outlet. The pipe axis at the inlet is horizontal and at the outlet it is 1 m higher. By neglecting friction, calculate the force and its direction if the inlet pressure is 100 kN/m² and the flow of the water through the pipe is 0.3 m/s. The volume of the pipe is 0.075 m³? L PI U₂ A₁ Fig. 4 P2 U2 A2 ور T
Water flows at a rate of 107L /s round a 1510 contracting pipe bend which lies in a horizontal plane. The diameter at the bend entrance is 771mm and at the exit 418mm. If the pressure at the entrance to the bend is 256kN/m2, determine the resultant force in the Horizontal direction (taking to the Left as positive) exerted by the fluid on the bend, correct to the nearest N. (Use π = 3.14)
a. Determine the magnitude of the projected component of the 100-lb force acting along the axis BC of the pipe. b. Determine the angle 0 between pipe segments ВA and BC. B 3 ft `8 ft 4 ft 6 ft 2 ft F = 100 lb D C
Question 02 A tapering pipe bend (in horizontal plane) is supported at point A and connected to a water flow system by flexible couplings at sections 1 and 2, as shown in Figure Q2. Find the torque, T, that must be resisted at support A. The gauge pressures at sections 1 and 2 are 720 kN/m² and 476 kN/m², respectively. Flow rate along the system is 0.045 m³/s. 50 mm 75 mm 300 mm Figure Q2 T 250 mm
The sector gate UE is submerged in water as shown in the figure. The sector gate is one-twelfth of a circle of radius 3.34 m. It has a length of 6.9 m. Determine the horizontal components (kN) of the resultant force acting on a gate. Water TIRETK 3 radius 0
Q2. Determine all forces acting on body A for the system shown in figure 2. Body A weighs 200 N and the cylinder B weighs 500 N. assume all the contact surfaces are smooth. 24 ring Cable 7 A r= 0.5 m 30 0.5 m B 2 m 1m 1 m 30°
The linkage for a hydraulic jack is shown. If the load on the jack is 2000 lb, determine the pressure acting on the fluid when the jack is in the position shown. All lettered points are pins. The piston at H has a cross-sectional area of A = 2 in². Hint: First find the force F acting along link EH. The pressure in the fluid is p= F/A. %3D 2000 lb 2 in. 2 in. 30 in. 60° 5 in. Н E F
SOLVE FOR THE FOLLOWING USING PRESSURE-PRISM METHOD 1. A tank is filled to a depth of 5 feet of water and is 8 wide by 10 feet long. Determine the hydrostatic force acting on the horizontal bottom and on the vertical ends of the tank. 2. The gate shown is rectangular and has dimensions 6 m by 4 m. What is the 3 m Hinge reaction at point A? Neglect the weight of the gate. Atmospheric pressure Stop 30 6 m Water
6.) The section of a gate at the end of a tank is shown below. The length of the gate is 3 m normal to the paper and hinge at O. If the depth of water is 2.50 m, neglecting the weight of the gate calculate the distance of the line of action of vertical component of the hydrostatic force on the submerged curved section of the gate from the y-axis. Use unit weight of water 9.80 kN/m^3. fluid mechanics