LR phase shift control is used in a controlled rectifier. If the value of the inductor is 100 mH, find the minimum and maximum value of the control resistor if the ratio of Idc/Idcmax is to be 0.1 to 0.9.

Q: A circuit has an ac voltage source and a resistor and capacitorconnected in series. There is no…

A: It is given that: V=900 VVC=500 Vω=20 rad/sR=300 Ω

Q: 2. For the voltage feedback network of Fig., determine: a) Ic b) Vc c) VE d) VCE

A: Given:

Q: Solve for the equivalent resistance and the total current. 48 V 4Ω 20 Ω www 5Ω 24 Ω ΑΛΛΑ 8 Ω 15 Ω…

A:

Q: draw a multiplier circuit that can calculate upto 32. (urgent)

A: Array Multiplier The multiplier circuit is based on the add shift algorithm. The main advantage of…

Q: For the network shown in Fig. determine the following a) IB b) Icoc) VCE, d) Vc e) VB 20 V 510 k 190…

A:

Q: 2. For the voltage feedback network of Fig., determine: a) lc b) Vc c) VE d) VCE

A: It is given that:

Q: Q.)  The circuit shown below is an idealized forward converter. Assuming an input voltage Vd=40V,…

A: The forward converter, a DC/DC converter, raises or lowers the output voltage and offers galvanic…

Q: What is the equivalent capacitance in nF if three capacitors of 6 nF, 1.9 nF, and 7.4 nF are…

A:

Q: 1) A coil composed of 100 turns has an inductance of 5 mH. If the number of turns is doubled without…

A: Given: A coil has following specifications, Initial turs, N1=100 Inductance, L1=5 mH Number of turns…

Q: In the figure shown below, if, R3 = 502, determine v. 10 V R₁ = 20 52 www R₂=. 2012 Ry

A: Given circuit: R3=5 Ω

Q: 2. The below figure shows the results of magnetic particles inspection experiment. What can you…

A: Introduction: Magnetic particle inspection is non-destructive testing to determine any discontinuity…

Q: Section 3.7 39. For the circuit shown in Figure 3.61, determine the total circuit current. 10 V Rs…

A: Given data, Circuit diagram is given as,

Q: 9.9 Answer: Use a A-to-Y transformation to find the current I in the circuit shown. I = 4/28.07° A.…

A:

Q: VL 0 10V -15V T t

A:

Q: Exercise Determine the transfer function of the network below: vi(t) (+) 192 1 H W0000+ 192 2F vo(1)…

A:

Q: Q5 T(s) = 62.5(x + 2.5) (s² +65 +25)(s+ 6.25) a) What are poles and zeros of the transfer function…

A: For the given transfer function answer the following Questions : Ts=62.5s+2.5s2+6s+25s+6.25 or we…

Q: For the circuit shown in Fig. calculate the maximum values of di/dt and dv/dt for the SCR 10 A 0.15…

A:

Q: 1- A source emf of 5 V supplies a current of 3A for 10 minutes, the energy provided in this time (a)…

A: We need to find out energy for given voltage and current .

Q: Relation between currents according to KCL is

A: In this case, the relation between the currents needs to be determined:

Q: The logic circuit shown in the given fig.2 can be minimised to X Yo

A: A gate logic circuit is shown below. We have to minimize the gate logic circuit.

Q: 2- Using the nodal analysis to find V₂ for the network. 3LER, ISA RIZER. Iz 2A R3 452 R₂&n 4A + V₂

A:

Q: Estimate the number of resistance of each section of a starter of 10 kW; 450 volts D.C. series…

A: We have an D.C series motor with,  KW rating = 10 KW Voltage (V) = 450 V Efficiency of motor= 78 %…

Q: 3- Using D-Y or Y-A conversion, find the current I in the network R₁S. I 1/1K2 кл TOV E R₂2K R6 WW 2…

A: Using Delta to star or star to delta conversion calculation of current I for the given circuit. If…

Q: The phase shift oscillator circuit shown, is designed to oscillate at 155 [Hz]. Determine the value…

A: The phase shift oscillator circuit shown, is designed to oscillate at 155 [Hz]. Determine the value…

Q: 16. Find the closed loop 3-dE frequency B=4MHz, R₁=3

A: Given data, Unity gain frequency B=4 MHz Input resistance, Ri=3 kΩ Feedback resistance, Rf=152 kΩ

Q: 2. For the voltage feedback network of Fig., determine: ܐܢ ܢ ܝܢ a) lc b) Vc c) VE d) VCE VI 10μF H…

A:

Q: Que 3.9. In the Fig. 3.9.1 shown, the ideal switch has been open or a long time. If it is closed at…

A: Solution !!

Q: A dc motor with its rotor and field coils connected in series has an internalresistance of 2.00 Ω.…

A: Given data: The internal resistance r=2.00 Ω The voltage V=120 V The current I=4.00 A

Q: When giving presentations, many people use a laser pointer to direct the attention of the audience…

A: Given,Power= 3 mWSpot diameter= 2mmFrom this,Spot area will be πd22A=π×222   =π mm2For a perfectly…

Q: What is the mass of an assembly of 1000 protons?

A: In this case, the  total mass of an assembly of 1000 protons needs to be determined.

Q: Q1- Calculate the current passing through the resistor 16 2 using Norton's theorem. (8 Marks) 20 V […

A:

Q: Calculate the maximum frequency deviation for the FM signal v(t) = 10 cos (6000t+ 5sin2200t)

A: Given information: The expression of the FM signal is vt=10cos6000t+5sin2200t The maximum frequency…

Q: 7.27. A linear time-invariant discrete-time system has transfer function 3z H(z) = (z+0.5)(z- 0.5)…

A: Given:- transfer function Hz=3zz+0.5z-0.5 Output response, yn=0.5n-3-0.5n+4un We have to find…

Q: Find Thevenin's equivalent between a & b 250 10V 30 ww 70 80 15V 20 20V a

A:

Q: Current source shown below is converted in to voltage source. Choose the correct voltage source…

A: Given data, Given circuit diagram is,

Q: 17. What is the share of renewable energies on the total electrical energy generated for 2019/2020?…

A: Introduction:. Electricity is produced using all sources of renewable energy. Geothermal steam is…

Q: Explain why static calibration is essential for unstable and highly responsive control system?

A: Introduction: The measurement equipment calibration has two aims. It determines the measurement's…

Q: Current source shown below is converted in to voltage source. Choose the correct voltage source…

A:

Q: A numeric system (e.g. a numeric keypad) generates numbers 0 to 9 in binary. You are asked to design…

A: To approach for the given problem first assume some inputs to the above numeric system.Since result…

Q: Calculate the maximum frequency deviation for the FM signal v(t) = 10 cos (6000t+ 5sin2200t)

A: The expression of the FM signal is given as vt=10cos6000t+5sin2200t

Q: In a 66 KV system the phase is ground capacitance is 0.05 µF and inductance is 2H. The voltage (kV)…

A: Given a 66 kV system with, Capacitance, C=0.05 μF Inductance,k L=2 H Current that be interrupted,…

Q: Question 1 Quuo Determine the amount of current (mA) flowing in the circuit if the charge seen at…

A: Given: Charge seen at cross sectional area, Q=0.0052C Time, t=30ms

Q: explain project scope management process completely and their techniques.

A: Find the answer below. The complete amount of work required to achieve a good, service, or outcome…

Q: Calculate the maximum frequency deviation for the FM signal v(t) = 10 cos (6000t+ 5sin2200t) a. 2200…

A:

Q: e = v2 40 sin (10*t + 20°) %3D (i) Determine the currents i1 and iz. (ii) Calculate the current is.…

A: The given circuit diagram is shown below: It is given that: e=2×40 sin104t+20° Vor, e=56.568 ∠20° V

Q: State and explain Carson's Bandwidth Frmula. Need urgently help. |

A:

Q: Find lo lo = Blank 1 Α 10 V (+ 8 Ω www 1ο 3Ω 6Ω

A:

Q: 2. The power of a circuit is giving as follow: p(t) = 150e(-10t) Calculate the total energy of the…

A: Given data, Signal is given as,  pt=15e-10t

Q: The Venus orbiter has a parabolic high gain communications subsystem with specifications provided in…

A:

Q: Find the Boolean expression for logic circuit shown in Fig.1 below and reduce it using Boolean…

A:

Electrical Power Generation

In an electric power generator, one type of energy is converted into electrical energy. Power-generating systems are simply a combination of potential or stored energy that is converted to provide kinetic energy, which, in turn, generates electrical energy for use in engines, lighting, heating, and other benefits of modern life.