In the given circuit, a step down transformer with an RMS voltageas 110V /11-0-11 V is used with RL = 1 KO.Assume diode as Germanium and the input frequency is F= 50HZ.D,CTVinRLD21- Name the given circuit.2- Find The PIV.3- Find Current trough load resistance.4- Draw the Input and Output wave forms.all

Note: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

In the given circuit, a step down transformer with an RMS voltage as 110V / 11-0-11 V is used with RL = 1 KO. %3D Assume diode as Germanium and the input frequency is F= 50H D, CT Vin RL D2 Name the given circuit . Find The PIV. Find Current trough load resistance. Draw the Input and Output wave forms. 00000

In the given circuit, a step down transformer with an RMS voltage as 110V / 11-0-11 V is used with RL = 1 KO. %3D Assume diode as Germanium and the input frequency is F= 50H D, CT Vin RL D2 Name the given circuit . Find The PIV. Find Current trough load resistance. Draw the Input and Output wave forms. 00000

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the given circuit, a step down transformer with an RMS voltage as 110V/11-0-11Vis used with R = 1 KO. Assume diode as Germanium and the input frequency is F= 50HZ. D, VI R D2 1- Name the given circuit. 2- Find The PIV. 3- Find Current trough load resistance. 4- Draw the Input and Output wave forms.
What is the value of the average voltage at the output of the circuit in the figure, knowing that: Voltage at the transformer output is equal to 5 Vac and the four diodes are from the 1N4001 family.
In the given circuit, a step down transformer with an RMS voltage as 220V/ 22 V is used with R = 3 KO. Assume diode as Silicon and the input frequency is F= 70 Hz. D3 D1 AC in D2 D4 LOAD 1- Name the given circuit 2- Find The PIIV. 3- Find Current trough load resistance. 4 Draw the Input and Output wave forms.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Vaue (t). 10 k. 8V 10 kN. D2 RL Vourlt) Vin= Vin(t) Ims D1 6V -8V 4V Page | 1
In a given circuit below is connected to an AC signal with 240V peak in a 4:1 transformer.Sketch the voltage wave form at V A and V o as practical diode
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 RL out OV 10 kN IN4001 alll
The ripple factor for pure dc is Answer: For the given circuit below, it operates on a peak-to-peak input voltage of 390.1 V, F= 60 Hz household supply through a step-down transformer with turns N1 = 10 and N2 = 1. Silicon diodes are used with a 1 Kiloohms load. Determine the output peak voltage (in volts). D1, D2 AC Input Vsec (Source) .03 D4 Load O 27.31 O 18.11 O 13.93 O 20.91
If a full-wave bridge circuit is used with a transformer whose secondary provides 50 V rms, the PIV across the diodes is about:
In a given circuit below is connected to an AC signal with 240V peak in a 4:1 transformer. Sketch the voltagewave form at VA and Vo as practical diode. (Show Complete Solution)
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
A 20-V-rms 60-Hz ac source is in series with an ideal diode and a 100-Ω resistance. Determine the peak current and PIV for the diode.