Design a voltage regulator circuit to supply a constant voltage of (10 V) across a resistiveload of (10 2). The minimum Zener current is (50 mA) and maximum current is (800 mA).Assume Rs = 10 S and Find: -1- the maximum and minimum source voltage.2- at the maximum source voltage, find the minimum load resistance.3- at the minimum source voltage, find the maximum load resistance.4- minimum and maximum power dissipated in the Zener diode.SC

Since you have asked multiple questions in a single request, we will be answering only the first…

Answered: load of (10 2). The minimum Zener…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Stringing of cells in a PV panel Draw the tabbing and bus-bar wires for a 72 cell module using three substrings and a junction box mounted in the typical central location. Each substring is protected by a bypass diode. No precision drawing is needed (i.e. you don't need to draw every single cell, the main arrangement of substring and how you connect to the jnction-box is relevant.
3phase half wave rectifier ,the line voltage(460v).load resistance(R-202).find Vdc, Vrms, PIV, RF, FF. Ans:
Design a Zener diode voltage regulator with a suitable circuit diagram and to consider the voltage regulator is used to power a cell phone at 4.5 V from a lithium ion battery pack, which voltage may vary between 5 V and 7.8 V. The current in the phone will vary 10 mA (when standby mode) to 150 mA (when talking). Assume that the Zener diode current, Iz(min) is 10% of Iz(max).
Determine the VDS and the drain current for the E-MOSFET circuit shown. The data sheet for this particular MOSFET gives ID(ON)=500 mA at VGS=10 V and VGS(th)=1 V.
TEST Read the question carefully. Write the letter for each correct answer in the blank space provided. A 1. Maximum power is delivered from a source of power to a load when the a. load current is equal to the power source current b. impedance of the load is equal to the output impedance of the power source c. output impedance of the power source is high compared to the impedance of the load d. output impedance of the power source is low compared to the impedance of the load 2. The emitter follower is a (an) a. impedance matching device b. high gain voltage amplifier c. phase inverter d. combination power and voltage amplifier 3. The emitter follower uses a. no collector resistor b. a forward bias collector-base junction c. negative feedback (degeneration) d. an NPN transistor only 4. The emitter follower has output resistance. a. high, high b. low, low c. low, high d. high, low input resistance and 5. The current gain of an emitter follower is a. less than 1 b. equal to 1 c. greater…
%3D For the circuit shown in Figure B23, a = 0.97, calculate the following: i. Collector current (Ic) ii. Collector-Base voltage (VCB) iii. Emitter Current (IE) iv. Base Current (IB) IE Ic 2.5 k2 Ouput 2.8V IB 10V VEE Vcc Figure B23
a)circuit diagram with a load ,for the JFET. b)input and output waveform c)equations for the output ( v and i)
a. A 220 ohms resistor is connected in series with the gate of an SCR using basic circuit in figure. The gate current required to fire the SCR is 10mA.What is the input voltage (Vin) is necessary to switch on the SCR?
Design and simulate the circuit in figure 2 using Multisim software and get the following parameters  Current in circuit I =…………………………mA Voltage across R1 ER =…………………………V Voltage across L1 EL =…………………………V Power dissipated P =…………………………mW
Briefly describe the operation of a silicon n-channel JFET, including effect of the gate voltages VG = 0 and VG < 0 and source-drain voltages Vos on the flow of charge carriers in the device before and after 'pinch-off'. Use an l-V graph to illustrate your answer. 4. Gate Source Drain FIGURE CREDIT: An Introduction to Semiconductor Devices, D. Neamen
For the circuit shown in Figure Vec= 22 V, Re= 5.6Kr Nc %3D R8- 330k2, B= 80 Rc Rg %3D Find the solution to Vi everything that comes 1_value of Zo .....ohm . NOTE: 1.2ks 3 The value of re is . . h is When the output is taken from the Emitter terminal of 0.47ks3 the transistor as shown in Figure. CE 2 The value of Zi is 4 The value of Ai is . ww

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

load of (10 2). The minimum Zener current is (50 mA) and maximum current is (800 mA). Assume Rs = 102 and Find: - 1- the maximum and minimum source voltage. 2- at the maximum source voltage, find the minimum load resistance. 3- at the minimum source voltage, find the maximum load resistance.