) For the following circuit, answer the following questions given that : Vz = 10 V, Iz= 25 mA, IzK= 1mA, Zz =72, PD(max) = 1 W at 50 °C. RA (0)=500 Determine the minimum and the maximum input voltages VIn (min), VIN (max) that can be regulated by the zener diode. Also, determine the line regulation. a) If a load resistor is connected, determine the minimum value of this load resistror RL(min) that can be used when VIN is set at 15 V.

) For the following circuit, answer the following questions given that : Vz = 10 V, Iz= 25 mA, IzK= 1mA, Zz =72, PD(max) = 1 W at 50 °C. RA (0)=500 Determine the minimum and the maximum input voltages VIn (min), VIN (max) that can be regulated by the zener diode. Also, determine the line regulation. a) If a load resistor is connected, determine the minimum value of this load resistror RL(min) that can be used when VIN is set at 15 V.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Answer all the questions one by one and solve all the unknown values with correct details
Izmin=0.1mA
1- A 9.1V Zener diode at test current of 28 mA. The incremental resistance is 52. Find Vzo and the Zener voltage at a current of (a) 10 mA. (b) 100 mA.
H.W4 The diode in the single-phase half wave rectifier has a reverse recovery time of tr frequency = 5 kHz. 150usec and the source voltage V₁ = 200V at Calculate the average output voltage. EP
Consider the circuit shown in the figure below with Ry=13 ko and R=9 kO. The Zener diode voltage is Vz = 3.5 V, then the currents Iz and , respectively, are equal to: R1 ww 20 V O a. 1.280 mA, 0.789 mA O b. 0.680 mA, 0.189 mA O c. 0.880 mA 0.389 mA O d. 1.080 mA, 0.589 mA
Sketch the transfer characteristic vo versus vi for the limiter circuit shown below. All diodes begin conducting at a forward voltage drop of 0.5V and have of 0.7V when fully conducting at 1mA.
Base from the values given. Fill in the questions.
A silicon diode has 1 ampere DC of current in biasd mode. What is voltage drop across the diode?
diode zener a, DESIGN THE NETWORK IN THE FIGURE, TO KEEP, "VL" at 12 V for a variation in load (IL) from 0 to 200 mA, DETERMINE "Rs" and "Vz" b. determine "P2min" for the Zener diode from section a
Assuming an ideal diode, sketch Vị, Và and ia for the half-wave rectifier below. The input is sinusoidal waveform with a frequency of 60 Hz. Also, determine and sketch V, and ir Ideal V-2 V 2.2 ka R 6.8 ka
Q2/ Determine the minimum input voltage required for regulation to be established in the figure. Assume an ideal zener diode with Izx 1.5 mA and Vz 14 V. R S60 1 Ves
Determine the output waveform of the biased clipper below using the simplified diode model.a.) Analyze the behavior of the circuit and fill up the table below. Vin Diode State (Forward Biased or Reversed Biased) Vout 5V 7V 0V -3V -6V b.) Draw the output waveform.