A 4-ft-long tube with the cross section shown in the figure is made of aluminum. Find thetorque that will cause a maximum shear stress of 10 000 psi. Use G = 4 10° psi for aluminum.+ 4 in. →|+ 0.04 in.0.08 in.4 in.

Answered: Image /qna-images/answer/d3613c63-1730-4d07-aff0-b3dcc1aa97dc.jpg

It-long tube with the cross section shown in the figure is made of aluminum. Fir that will cause a maximum shear stress of 10 000 psi. Use G = 4 10° psi for alum + 4 in. →| - 0.04 in. 0.08 in." 4 in.

It-long tube with the cross section shown in the figure is made of aluminum. Fir that will cause a maximum shear stress of 10 000 psi. Use G = 4 10° psi for alum + 4 in. →| - 0.04 in. 0.08 in." 4 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Is this a frame or a truss? Calculate the cross section of the bar BC if the allowable normal stress…

A: Given:- Allowable normal stress in BC = 165 MPa To determine- a) Is this a frame or a truss? b)…

Q: beme Strength of Materials modoMa0 نلود Dr. Mohammed Hashim Mohammed Problems that years make great…

A: A = 150 mm2P = 5 kN or 5000 N = 11.7 x 10-6/oCE = 200 x 109 N/m2 or 200,000 MPaor 200,000 MPa

Q: Problem 317 A hollow bronze shaft of 3 in. outer diameter and 2 in. inner diameter is slipped over a…

Q: An aluminum [E = 9100 ksi] control rod with a circular cross section must not stretch more than 0.23…

Q: n aluminium channel section is shown in the figure below: 4mm I; mm mm l mm s indicated, the…

Q: A steel cylinder is enclosed in a bronze sleeve, both simultaneously supports a vertical compressive…

Q: A flat steel bar, 30 mm wide by 4 mm thick and 1.7 m long, is bent by couples applied at the ends so…

Q: A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel [E = 29,000…

A: To determine: normal stress in the polymer cylinder normal strain in the polymer cylinder normal…

Q: 5 The supports of Beam AD are aluminum rod and st eel rod only. Determine the stress in the aluminum…

Q: A SHAFT COMPOSED OF SEGMENTS AC, CD, AND DB IS FASTENED TO RIGID SUPPORTS AND LOADED AS SHOWN IN…

A: DETERMINE THE MAXIMUM SHEARING STRESS DEVELOPED IN EACH SECTION

Q: 3 ft 4 ft 7. The 2P P Aluminum A = 0.6 in.2 E = 10 x 10° psį Steel - A = 0.4 in.2 E = 29 x 106 psi…

Q: Q3 Answer either A or B: A. Determine the design moment strength of 3 No. 19 the section shown in…

Q: An aluminum bar having a cross-sectional area of 160 mm² carries the axial loads as shown in the…

A: Axial load on the bar: The outcome of a force that passes through the centroid of a segment and is…

Q: Use hand written solution. Nscp 2015 steel design ty

A: To solve the problem of determining the load capacity of the column made of two channels C250×30…

Q: A steel cylinder is enclosed in a bronze sleeve, both simultaneously supports a vertical compressive…

A: Given :

Q: CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between…

Q: An aluminium channel section is shown in the figure below: i mm 1; mm mm I mm As indicated, the…

A: Given L1=167mm t1 =1mm L2 =218mm t2=3mm

Q: A metal bar do in diameter and l, gage length failed under an axial tensile load of F. The final…

A: Engineering stress is the ratio of force applied and the initial cross-sectional area of the bar.…

Q: The bar MNOP rigid bar is pinned at N and connected to two vertical rods. Assuming that the bar was…

Q: The wooden beam shown is made by gluing together planks as shown. 8 kN/m Glue 80 mm 80 mm - NA 6 m…

A: Determine the maximum shear stress in the glue in kPa.

Q: The compound bar carries axial loads as shown. Determine the maximum allowable value of P if the…

Q: GIVEN: Solid aluminum bar shown: 4 in. by 4 in. E = 10 x 10° psi oy = 36 ksi 4000 & 200016 4000 16 B…

A: A) Load in each section of bar PAB = 4000 lb ( T ) PBC = 4000 - 2000 = 2000 lb ( T ) PCD = 4000 -…

Q: Knowing that P = Q = 480 N, determine (a) the distance a for which the absolute value of the bending…

Q: Determine the compressive force (in Ib) in the bars shown after a temperature rise of 170°F if d =…

A: To find out the compressive force in bar.

Q: The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that…

A: Given:- Allowable stress in steel=182 MPaAllowable stress in bronze=60 MPaD=0 To find:- Largest…

Q: A sn of Ex = 0.40x10-3 and Ey = 0.30x10-3, determine o, . Use E=110 GPa and v = 0.35 Oy

A: Given : ∈x=0.40×10-3∈y=0.30×10-3μ=0.35E = 110 GPa = 110×103 MPa

Q: Consider the given figure. The bar AC is 6 mm thick and is made of a steel with a 425 MPa ultimate…

A: Given:- The thickness of the bar AC (t) = 6 mm The ultimate stress of the steel = 425 MPa The…

Q: The temperature of the cylindrical rod is heated to 45°C which is fixed in between A and C rigid…

Q: Find the stresses in A, B and C?

Q: hown in the figure. The properties of the segments and the work ble. Determine the maximum allowable…

A: Solution: For compound bar (Steel section) Ast=0.75in2Est=30×106 psiLst=2×12=24…

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

Q: Internal diameter of a steel shaft is 70% of external dia and the shaft has to transmit 3500 kW at…

A: Given Data :→Internal dia Di of shaft =0.7External dia Do→Shaft Power P = 3500 kW→n=200 rpm→Maximum…

Q: Internal diameter of a steel shaft is 70% of external dia and the shaft has to transmit 3500 kW at…

A: Given: Internal diameter of a steel shaft is 70 % of external dia. di=0.7do Shaft transmitted power,…

Q: t p= 0.2N2 in P = 500 lbf 3 1.N1 in 2p h = H -2p Material: Aluminum (E=10.0x106 Ib/in?, v= 0.3)…

A: Given N1=7 and N2=0Height of the section H=1.N1=1.7 inand thickness ρ=t=0.2N2=0.20 inreduced…

Q: A fully bonded aluminum shell and steel inner Outer core bar is axially loaded. Find the normal…

Q: The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum…

A: Aluminum EAl = E1 = E2 = 71 GPA d1 = d2 = 17 mm Steel Es = E3 = 190 GPA d3 = 18 mm

Q: 18 in. 6 in. 18 in. P A Steel B C Steel D -Aluminum 6. The compound bar ABCD has a uniform…

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

A: Given: P = 210N, a = 230 mm , b = 130mm, d = 26 mm

Concept explainers

Pressure and Stress

Question

A 4-ft-long tube with the cross section shown in the figure is made of aluminum. Find the
torque that will cause a maximum shear stress of 10 000 psi. Use G = 4 10° psi for aluminum.
+ 4 in. →|
+ 0.04 in.
0.08 in.
4 in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The compound shaft shown is attached to rigid supports. a Bronze B Steel For the bronze For the steel Diameter = 100mm Diameter = 50mm G= 35GPA G= 83GPA Sallowable= 45MPA SSallowable= 55MPA. Lbr= 2.13 a. determine the ratio of the lengths of the bronze and steel so that each material will be stressed to its maximum permissible limit b. determine the maximum torque carried by the bronze. C. what is the relative angle of twist with respect to the support if max torsion is applied at B.
Please provide complete and step by step solution (including FBD)
The two wooden boards shown in Figure are connected by a 0.5-in.-diameter bolt. Washers are installed under the head of the bolt and under the nut. The washer dimensions are D = 2 in. and d = 5/8 in. The nut is tightened to cause a tensile stress of 9,000 psi in the bolt. Determine the bearing stress between the washer and the wood. Please explain the solution
i need the answer quickly
dont round off if not yet the final answer pls
Question 4. Three wires are used to suspend the plate shown. Aluminium wires are used at A and B with a diameter of 3 mm and a steel wire is used at C with a diameter of 2 mm. Knowing that the allowable stress for aluminium (E = 72 GPa) is 96 MPa and that the allowable stress for steel (E = 200 GPa) is 124 MPa, determine the maximum load P that may be applied. L L P B
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 13 mm and an elastic modulus of E = 70 GPa. The steel rod has a diameter of 20 mm and an elastic modulus of E = 190 GPa. Assume a = 4.8 m, b = 1.9 m, and c = 1.2 m. What is the magnitude of load P that is necessary to displace point A 14 mm to the left? a b (1) P Answer: P = i (3) B KN O
Round off final ans, dont round off initial values
Portions of a x-in. square bar have been bent to form the two machine components shown. Knowing that the allowable stress is 18 ksi, determine the maximum load that can be applied to each component. (a) 1 in. (b) The maximum load that can be applied to component (a) is The maximum load that can be applied to component (b) is lb. lb.
1.A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are € E =0.40x10-3 and ɛ =0.3 x 10- determine O and o. Use E = 110 GPa and v=0.35. y y. = Blank 1 MPa Answer in 1 decimal place = Blank 2 MPa Answer in 1 decimal place
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises after a load W = 120 kN is applied. Steel rod Bronze rod A (mm²) 350 1500 a (/°C) 11.7 x 10-6 18.9 x 10-6 E (GPa) 200 83 O Steel 1.5 m 1.0 m- 2.5 m 9. Determine the stress at the steel rod in MPa when there is a temperature rise of AT = 36 °C. W Bronze 3 m 1.5 m-