The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 13 mm and an elastic modulus of E = 70 GPa. The steel rod has a diameter of 20 mm and an elastic modulus of E = 190 GPa. Assume a = 4.8 m, b = 1.9 m, and c = 1.2 m. What is the magnitude of load P that is necessary to displace point A 14 mm to the left? a b (1) P Answer: P = i (3) B Po KN O

The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 13 mm and an elastic modulus of E = 70 GPa. The steel rod has a diameter of 20 mm and an elastic modulus of E = 190 GPa. Assume a = 4.8 m, b = 1.9 m, and c = 1.2 m. What is the magnitude of load P that is necessary to displace point A 14 mm to the left? a b (1) P Answer: P = i (3) B Po KN O

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.3P: Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2...

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 63 GPa. The steel rod has a diameter of 24 mm and an elastic modulus of E = 215 GPa. Assume a = 4.2 m, b = 1.4 m, and c = 1.2 m. What is the magnitude of load P that is necessary to displace point A 13 mm to the left?
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 19 mm and an elastic modulus of E = 69 GPa. The steel rod has a diameter of 18 mm and an elastic modulus of E = 195 GPa. Assume a = 3.6 m, b = 1.5 m, and c= 0.8 m. What is the magnitude of load P that is necessary to displace point A 11 mm to the left? (1) (3) B (2) Answer: P = i kN
QUESTION 3 The assembly consists of three steel rods and a horizontal bar BED. The structure supports a 36 kN load P located at middle of bar BED. Each of the rod AB and CD has a cross-sectional area of 200 mm² and rod EF has a 625 mm². Modulus of elasticity for steel is 200 GPa. Determine: (a) The change in length of rod EF. (b) The stress in each rod. 500 mm 400 mm
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. Thesteel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assume a = 4.1 m, b = 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? (1) P (3) B (2) Answer: P = 117.7 kN
Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
Q # 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. The value of P is limited to 20 KN in bronze, 72 KN in aluminum and 28 KN in steel Find the area of each section that will not exceed a stress in steel of 280 MPa, in aluminum of 180 MPa, or in bronze of 200 MPa. CLO -2 Steel Aluminum Bronze 2P 4P 2.5 2.0 1.5
An aluminum [E = 9100 ksi] control rod with a circular cross section must not stretch more than 0.23 in. when the tension in the rod is 2100 lb. If the maximum allowable normal stress in the rod is 10.9 ksi, determine: (a) the smallest diameter d that can be used for the rod. (b) the corresponding maximum length L of the rod. Answers: (a) d = (b) L = i i in. in.
A ngid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D. as shown Neglect deflections of the bar due to bending Use E200 GPa What is the displacement of the loaded end of the bar? 2 Determine the tensile stress induced in rod CD by the 80 kN load the alowable stress in rod CD is 124 MPa, what weight W can be safely applied?
A steel bar with diameter d1 = 10 mm has upset ends with diameter d2 = 15 mm. The lengths of the bar segments are L1=0.3 m and L2=0.15 m. The radius at the transition R = 1.25 mm and the modulus of elasticity is 90 GPa, the bar product of the load p elongates 0.12 mm maximum stress