Consider the given figure. The bar AC is 6 mm thick and is made of a steel with a 425 MPa ultimate stress. What should be its minimum width m if the structure shown is being designed to support a 12-kN load P with a factor of safety of 2.5? Tercümesi: Soru 1: Verilen şekli göz önüne alın. AC çubuğu 6 mm kalınliğındadır ve 425 P. MPa nihai gerilim (uitimate stress)" e sahip 800 mm bir çelikten yapılmıştır. Gösterilen yapı 2.5 güvenlik faktörü ile 12 kN'luk bir P yükünü DA90 destekleyecek şekilde tasarlanıyorsa, AC bannın genişligi m ne olmalıdır? 480 mm 90 600 mm-

Consider the given figure. The bar AC is 6 mm thick and is made of a steel with a 425 MPa ultimate stress. What should be its minimum width m if the structure shown is being designed to support a 12-kN load P with a factor of safety of 2.5? Tercümesi: Soru 1: Verilen şekli göz önüne alın. AC çubuğu 6 mm kalınliğındadır ve 425 P. MPa nihai gerilim (uitimate stress)" e sahip 800 mm bir çelikten yapılmıştır. Gösterilen yapı 2.5 güvenlik faktörü ile 12 kN'luk bir P yükünü DA90 destekleyecek şekilde tasarlanıyorsa, AC bannın genişligi m ne olmalıdır? 480 mm 90 600 mm-

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.4P: A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
The light rigid bar ABCD shown Is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. E200 CPa E1m 2.0 m 0.6m 1.5 m VP-20 KN Aluminum E-70 GPa A=900mm2 L-1.5 m What is the axial stress at steel rod in MPa?
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
The 200-mm square aluminum block supports a compressive load of 300 kN. What is the normal stress acting on section a–a in MPa What is the shearing stress acting on section a–a in MPa The lapbelt assembly is to be subjected to a force of 800 N. What is the required thickness t in mm. of the belt if the allowable tensile stress for the material is 10 MPa?
A ngid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D. as shown Neglect deflections of the bar due to bending Use E200 GPa What is the displacement of the loaded end of the bar? 2 Determine the tensile stress induced in rod CD by the 80 kN load the alowable stress in rod CD is 124 MPa, what weight W can be safely applied?
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm? A = 400mm? A - 200mm 40KN 10KN 20KN 2.5m 2.0m 1.5m
ok Strength of Materials donO نورا حياتها مترجر شریه ✓t مقادم نلود Dr. Mohammed Hashim Mohammed Problems tan't yorada grutegraat km). E1.x² (1) A steel rod with cross-sectional area of 150mm² is stretched between two fixed points. The tensile load at 20°c is 5 kN. What will be the stress at -20°c? At what temperature the stress will be zero? bedre α = 11.7x10 6/2 and E = 200x10² N/m².
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to aodal loads as shown. If P-7 IN, Determine the total aodal deformation (in mm). Indicate negative sign f comoression. @ 5P O 3P E-200 6P 30 mm emm 80 mm 30 mn 30 mm
The modulus of elasticity of mild steel is equal to .. .? .... .. a. 2 x 10ʻN/m? a. 2 x 10'N/m 2 b. 2 x 10° N/m 4 c. 2 x 10 N/mm 5 d. 2 x 10 N/mm Check
A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areidentical except that initially the middle bar is slightlyshorter than the other bars (see figure). The dimensionsand properties of the assembly are as follows:length L = 1.0 m, cross-sectional area of each barA = 3000mm2, modulus of elasticity E = 45 GPa,and the gap s = 1.0 mm.(a) Calculate the load P1 required to close the gap.(b) Calculate the downward displacement d of therigid plate when P = 400 kN.(c) Calculate the total strain energy U of the threebars when P = 400 kN.(d) Explain why the strain energy U is not equal toPδ / 2. Hint: Draw a load-displacement diagram.
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.