It is well known that in a parallel pipeline system if you increase the diameter of those parallel pipes, it increases the capacity of the pipe network. But if we increase the length of the parallel pipes, what will be the impact on the capacity of the system happen? O The flow capacity of the parallel system will remain the same. O The flow capacity of the parallel system will decrease. O The flow capacity of the parallel system will increase. O It is unknown, depends on the parallel pipe diameter.

It is well known that in a parallel pipeline system if you increase the diameter of those parallel pipes, it increases the capacity of the pipe network. But if we increase the length of the parallel pipes, what will be the impact on the capacity of the system happen? O The flow capacity of the parallel system will remain the same. O The flow capacity of the parallel system will decrease. O The flow capacity of the parallel system will increase. O It is unknown, depends on the parallel pipe diameter.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For pipes in parallel, what condtions must be satisfied? O Flow is the accumulation of the flows throughout each branch pipe Head loss is a sum of the total (major and minor) head loss from entrace to exit The total head loss (major and minor) is equal throughout each branch pipe O The flow through each pipe is the same
ANSWER ASAP PLS.
Two reservoirs, A and B, are connected together by the two pipes with a pump between them. Assuming that the head loss in the pipes is given by hi = 0.015(L/d)(V/2g), where "L" is the length of pipe in feet and "d" is the pipe diameter in feet, determine (a) the velocity in each pipe, (b) the head added by the pump, and (c) the horsepower that must be supplied to the water to pump 2.5 cfs from the lower to the upper reservoir? El 140 ft B A El 90 ft L: = 2000 ft d: = 8 in. El 40 ft --- L; = 1000 ft d: = 8 in.
Water flows at a velocity of 10 m / s through a 90 mm radius pipe. a. Calculate and state what the flow regime is under these conditions. b. In order for the water flowing from the same pipe to be suitable for the transition regime and turbulent regime, the flow Calculate what / what the speed value range might be.
Question 7 (Parallel pipes) Two reservoirs are connected by two parallel pipelines with diameters of 0.8m and 0.6m as shown in Figure 8. The pipelines are both 3 km long with a value of 0.03. The combine discharge through the pipelines must be at least. Pipe 2 Pipe 1 Figure 8 a) When the total discharge is, what is the flow rate in the individual pipeline? b) What is the minimum difference in the elevation of the surface water level in the two reservoirs required to maintain a flow of through the pipelines?
Oil of specific gravity 0.802 and kinematic viscosity 0.000186 m /s flows from tank A to tank B through 305 m of new pipe at the rate of 0.089 m3/s. The available head is 0.161 m. What size pipe should be used?
What is the head loss between points A and D when the flow rate is 6² the flow rate for each of the branches (1 and 2) in the parallel pipes and the head o segment BC. Neglect Minor Losses B C D Pipe Segment Length (m) Diameter (m) Friction Coefficient (n) AB 100 0.75 0.014 150 0.5 0.008 90 1 0.035 75 1.25 0.021 CD 1 2
From the given three reservoirs shown. The elevation A is 346 m., B is at elevation 301 m and C is at elevation 241 m. Rate of flow at 1 is 200 liters/sec. PIPE LENGTH (M) DIAMETER HAZENS, C (MM) 450 600 120 3600 300 100 3 1200 D3 110 Determine the diameter of pipeline 3. 175 mm 177 mm O 180 mmm O 184 mm None of the above
3. **A 32800 ft long pipeline, of commercial steel with the nominal diameter of 12 inch of schedule number 40, conveys water from a reservoir (top water level 2790 ft above the sea level) to a water treatment plant (2230 ft above the sea level). Assuming that the reservoir remains full, and neglecting minor losses, estimate the volume flow rate. Take the viscosity µ = 1.00 CP.
The two lines shown are the EGL and HGL of a pipeline. Which statement is true? * (1 Point) A B The diameter of pipes in AB and BC are the same There is no velocity at end C O The slope of EGL in BC denotes head loss