Please help me on question 5. and 7. I do not know if I am doing it right.Thank you Voltage: 4VPart 2 – RLC Circuit1. Create a circuit with an AC Voltage in series with a resistor, inductor, and capacitor. Note also thecapacitance, inductance, and resistance as was done in Part 1.C = 0.10FL= 50.0HR- 10.0 f2. Right click the AC Voltage and click Change Voltage and note the current value of the voltage.Click Change Frequency and note the current value of frequency.V= 10,0 Vf = 0.50 Hz%3D3. Place Voltage Chart around each element in the circuit, include the AC Voltage. Make sure thepolarity is consistent.4. Mark the maximum/minimum voltage on each graph. Qualitatively note the similarities anddifferences between the graphs. Which graphs are in phase with one another? Which graphs are not?What about the sign of the amplitude?AC VoltageCapacitorResistorInductorMaximum, 1ovMaximum,MaximumMaximum: IoV.VoltageVoitageMinimumVoltageVotageMinimum-1OVMinimum .Vo HageMinimumVoltageVoltage-2v- IVVoltage5. Using the RMS voltages (V RMS = Vo / V2) show that the RMS voltage on the AC Voltage is consistentwith the voltage sum of each element VRMS = V [ (VRMS.R)^2 + (VRMS,L -VRMS,c)^2 ].%3DVems a 10.0V/2VRMS = (I0)2 + ( 50 - 0.10)²ニVRMS= 7.071067812vVRMS =50.892140885 V%3D6. Using the resistance, capacitance, inductance, and the frequency of the AC Voltage calculate theimpedance Z.Z= R?= 2 (0.50)( 50)5 157.0796327(XL- Xc)²(10)2+(157.07 96327. 3. 183098861)2154.2210852 S2: lan (0,50) Xe: 3.183098861こ7. Place a Current Chart after the battery in the circuit. Note the maximum value of the current. Usingthe RMS current show that the RMS voltage from the AC Voltage is consistent with the RMS currentand impedance.Maximum value of theCurrent: 0.06A

In the problem it is already given it is a series RLC circuit with R,L and C connected to it. The…

ircuit 1. Create a circuit with an AC Voltage in series with a resistor, inductor, and capacitor. Note also the capacitance, inductance, and resistance as was done in Part 1. C = 0.10F L= 50.0 H R- 10.0 2. Right click the AC Voltage and click Change Voltage and note the current value of the voltage. Click Change Frequency and note the current value of frequency. V= 10 O V

ircuit 1. Create a circuit with an AC Voltage in series with a resistor, inductor, and capacitor. Note also the capacitance, inductance, and resistance as was done in Part 1. C = 0.10F L= 50.0 H R- 10.0 2. Right click the AC Voltage and click Change Voltage and note the current value of the voltage. Click Change Frequency and note the current value of frequency. V= 10 O V

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

For the circuit in the figurea) Determine the time constant.b) Write the mathematical expression for IL, VL and VR, after the switch is closed.c) Determine IL, VL for one, three and five time constants.d) Draw the waveforms of IL, VL and VR.
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Vaue (t). 10 k. 8V 10 kN. D2 RL Vourlt) Vin= Vin(t) Ims D1 6V -8V 4V Page | 1
What voltage is boosted at the output of a multiplier.Choices: average, rms, peak, or instantaneous Which assumption is not used in the analysis of multipliers?Choices: a capacitor will not discharge, start with the cycle of the source that will forward bias the nearest diode, the output will always be multiplied, or a single diode is forward biased at a time A voltage multiplierChoices: multiplies the output voltage, has very high voltage and low current ,can employ inductors, or may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations atChoices: the input and output, the load, source, or in the environment Between a lower percent regulation and a higher one, which is better?Choices: lower or higher
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
Given the circuit in Figure 04 and defining that: Vs = 100 sin (wt) Volts and the firing angle of the thyristors T1 and T2 is equal to 110° and that T3 and T4 have similar firings in the negative half-cycle of Vs. a)Sketch the output voltage waveform for a highly inductive load. b) Sketch the waveform output voltage, replacing the highly inductive load with a purely resistive load. c) Get the value of the average output voltage when the load is purely resistive.
Full-wave rectified sine wave circuit is used to measure the RMS value of a half square wave with the help of PMMC meter. The meter was actually calibrated for sine wave. The circuit uses a meter movement with a full scale deflection current of 200uA and internal meter resistance of 5kΩ. Assuming Non-ideal diodes having resistance 1kΩ, Analyze the circuit to determine the value of series multiplier resister and the corrected RMS voltage, if meter is to read 225V RMS full-scale.
1. Which of the following answers best describes discontinuous conduction mode? A. The inductor voltage ripple goes negative B. The inductor current ripple stays positive C. The inductor current ripple falls to zero D. The output current ripple falls to zero
1. Describe the difference between the currents that exist in the wires leading to a capacitor when theses wires are connected to (a) a DC source and (b) an AC source.
(P-02) Diode Series (Course: Electronic Devices and Circuit Theory). -Use Equation Operators or write it down on paper/digital paper. -Redraw and Apply. -Please answer without abbreviation. Thank you.
Number 9 Please show your detailed solution. Number 9 Please show you detailed solution. A 50-ohm resistor is in series with a 40-?F capacitor across a constant potential source of 180 volts. Determine frequency that will give current of 3.13 amp. A. 250 Hz C. 160 Hz B. 200 Hz D. 140 Hz
4 Listed are some of the uses of capacitors except: A. couples AC B. bypassing a shunt load C. signal amplification D. filters pulsating DC
The signal measured with the oscilloscope in the Multisim program is shown in the figure below. For the signal measured according to this figure, write the following measurement values.T (period) = …………………… .. usf (frequency) = …………………… .. kHzVpk (Peak voltage) = ……………………. mVVpk-pk (Peak to peak voltage) = ………………. VVrms (Effective value) = ………………… V