In the piston-cylinder assembly in the figure, the first 1 kg at a temperature of 110°C and a pressure of 600 kPa There is refrigerant-134a. Later on this refrigerant-134a is saturated vapor until cooled. Then, balance the piston the holding pin is removed and an additional force By applying refrigerant-134a, saturated liquid until it is compressed. phase changes showing the total work done in a P-v diagram calculate.

In the piston-cylinder assembly in the figure, the first 1 kg at a temperature of 110°C and a pressure of 600 kPa There is refrigerant-134a. Later on this refrigerant-134a is saturated vapor until cooled. Then, balance the piston the holding pin is removed and an additional force By applying refrigerant-134a, saturated liquid until it is compressed. phase changes showing the total work done in a P-v diagram calculate.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5- During some actual expansion and compression processes in piston cylinder device, the gases have been observed to satisfy the relationship Py" = const.. Calculate: (1) the work done when a gas expands from a state 150 kPa and 0.03 m' to a final volume of 0.2 m for (n=1.3), and (2) show the process on P-V diagram
Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition. Initially, one part contains an indeal gas, and the other part is evacuated. The partition is then removed, and the gas expands into the entire tank. At the initial state, the mass of the gas is m= 4.00kg, initial pressure is p1 = 600.00 kPa, initial temperature is T1 = 300.00 K. The gas constant is R = 0.2870 kJ/(kg·K). (The internal energy can be determined by the equation ΔU=m·cv·(T2-T1), where cv = 0.7180 kJ/(kg·K) is the specific heat at the constant volume.) Calculate the final state temperature T2.__________ (K)
3000 kJ of heat is given to 1 kg of water at 20 C. If steam with a pressure of 750 kPa is obtained as a result of this process, is this steam wet?institution? You should reach the result by typing the table values and operation steps. TIP: You should decide on enthalpy values using Thermodynamic Property Tables.
Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition. Initially, one part contains an indeal gas, and the other part is evacuated. The partition is then removed, and the gas expands into the entire tank. At the initial state, the mass of the gas is m= 4.00kg, initial pressure is p1 = 600.00 kPa, initial temperature is T1 = 300.00 K. The gas constant is R = 0.2870 kJ/(kg·K). (The internal energy can be determined by the equation ΔU=m·cv·(T2-T1), where cv = 0.7180 kJ/(kg·K) is the specific heat at the constant volume.) Calculate the final state pressure p2.__________ (kPa)
X=6
2. In a free-moving piston-cylinder assembly with a pressure of 60 kPa and a temperature of -20°C100 grams of R-134a is initially retained. until the assembly temperature is 100°C.is heated. Calculate the volumetric change after heating.
An ideal gas is compressed from a volume of V, = 6.00 L to a volume of V, = 3.00 L while in thermal contact with a heat reservoir at T = 295 K as in the figure below. During the compression process, the piston moves down a distance of d = 0.145 m under the action of an average external force of F = 21.0 kN. (a) Find the work done on the gas. kJ (b) Find the change in internal energy of the gas. k) (c) Find the thermal energy exchanged between the gas and the reservoir. kJ (d) If the gas is thermally insulated so no thermal energy could be exchanged, what would happen to the temperature of the gas during the compression? O The temperature would decrease. O The temperature would remain constant. O The temperature would increase.
(b) A piston-cylinder device contains 0.6 m' air at 150 kPa and 30°C. The air is compressed according to PV"-constant to a pressure of 800 kPa and a temperature of 185°C. Assume air as an ideal gas with R -0.287 kJ/kg.K. i. Determine the polytopic index (n). ii. Calculate the work done, kJ. Sketch and label the process on a pressure versus volume (P-1) diagram.
I need the answer as soon as possible
Briefly explain all the Choices and Choose correct ( Draw Diagram if need )