In the I profile section, the tension force P acts eccentrically. b = 80 mm, h = 60 mm, t = 20 mm. a) Find the equation of the neutral axis and draw the neutral axis on the cross section. b) For the allowable compression and tension stress Oalow = 100 MPa, find the magnitude of maximum force P that the cross section can carry safely.

Q: A concrete beam has a width of 400 mm. It is reinforced at the bottom fiber with 4 – 28 mm deformed…

A: Answer we are given  f'c = 49 Mpa fy = 362 Mpa As = 4- 28 mm bars  As = 4 * π4*282 As = 2463 mm2  We…

Q: For the truss shown, determine the normal stress of member AE, FB and CD. Identify if the stress is…

A: For the truss given below, the normal stress of member AE, FB, and CD are to be determined.

Q: Q1. The beam has a inverse T-section. Determine the maximum tensile and compressive bending stress…

A:

Q: Given the beam shown with computedreactions and a cross section. 1. Draw the shear and moment…

A: As per bartleby guidelines,  experts are allowed to solve only first three parts . Those are solved…

Q: Design the maximum permissible value of W using a factor of safety of 2, based on the following…

A: Given Data: The thickness of the support plates are 2 inches. The cross-section of the member is 6×2…

Q: The internal shear force V at a certain section of an aluminum beam is 10.2 kN. If the beam has the…

A: Solution:

Q: 6-126. The wooden section of the beam is reinforced with two steel plates as shown. If the beam is…

A:

Q: The steel pipe AB has a 64-mm outer diameter and a 5-mm wall thickness. Knowing that arm CDE is…

A:

Q: Determine principal stress and maximum shear stress 200 MPa

A: Given data : Normal stress in X direction (σX)=350 MPaNormal stress in Y direction (σY)=-200…

Q: : A tripe-U shear mount used four 10 mm x 60 mm x 100 mm hard rubber blocks. Upon loading, the upper…

A:

Q: In order to reinforced a column in an existing structure, two channels are welded to the column as…

A: Given: Section: W 12 x 50 C 6 x 13 Effective length of the column, KL=4.9 m Fy = 350 MPa Fu = 450…

Q: 1. The beam is made up of the wood section that is glued together as shown. If the allowable stress…

A: Given- An I section Beam carrying UDL   Required- To determine the shear flow that must be resisted…

Q: Determine the shearing stress at the neutral axis. (in Psi). Note: include the negative sign in the…

A:

Q: Why is the force Fd pointing downwards? By force equilibrium, shouldnt  it be 3 + Fd = 9 Fd =…

A: yes, you are  right by equalibrium condition 3+Fd=9 we calculate reactions using the equailibrium…

Q: The steel beam has the cross section shown. The beam length is L = 30 ft, and the cross-sectional…

A:

Q: normal Ja-25° K → P= AB kN

A: Given data: P=53 KNA=1200 mm2α=25o Calculating normal stress on the plane a-a:…

Q: The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure…

A:

Q: A simply supported wood beam is subjected to uniformly distributed load q. The width of the beam is…

A: Given beam is simply supported with uniform distributed loadLength of span, L=17ftWidth of beam,…

Q: A simply supported beam has a maximum moment equal to 20 KN.m. The beam has a width of 200 mm and a…

A: step 1-

Q: The lap joint is connected by three 40-mm-diameter rivets. Assuming that the axial load P= 70 kN is…

A:

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

A:

Q: 9. The rigid bar ABC is supported by a pin at A L=4 ft and a steel rod at B. A = 0.5 in.2 E= 29 x106…

A:

Q: The internal shear force V at a certain section of an aluminum beam is 10.6 kN. If the beam has the…

A:

Q: Determine the largest weight W that can be supported by the two wires AB and AC. The allowable…

A: Given data in question  Stresses Area Angles To find out  Weight W value

Q: The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure…

A:

Q: The internal shear force V at a certain section of an aluminum beam is 10.5 kN. If the beam has the…

A:

Q: The truss shown consists of wooden members. Knowing that each member has a 100 x 100 mm. square…

A:

Q: Question 1. The plane NN' makes an angle 0-30" with respect to the cross section of theprismatic bar…

A:

Q: The piece of plastic is originally rectangular. After the application of force, it deformed in the…

A: L = 500mm B = 800mm ∆Cx = a = 2mm∆Cy = b = 1.5mm∆Dx = c = 4mm∆Dy = b = 1.5mm

Q: A load of P = 4261 N is acting on member AC. The length of AC is d = 320 mm. The cross-sectional…

A:

Q: The internal shear force V at a certain section of an aluminum beam is 10.2 kN. If the beam has the…

A: Given Data Width of flange = 69mm thickness of flange = 4mm Depth of beam = 72 mm Height of web =…

Q: The line of action of the 75-kip axial load Pis parallel to the geometric axis of the column AB and…

A: P = 75 kipx = 0.6 in E = 29 x 106 psi

Q: Determine the moment M that should be applied to the beam in order to create a compressive stress at…

A:

Q: Problem II. The midpoint B of the steel cantilever beam ABC is - Aluminum supported by a vertical…

A: A cantilever beam is a direct member of a building or structure which is rigid from one end and free…

Q: A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is…

A: The values given in the question are as follows: Width of beam(b)=310 mm Effective depth of…

Q: Design the beam wooden section of a simple span with 3.5 m in length. Use the given allowable stress…

A: bending stress theory used with some assumption. isotropic , homogeneous and elastic material is…

Q: Determine the location of the shear center for the following section. Determine the shear stress at…

A: Data Given: h1= 25mm h = 100mm b = 50mm Thickness = 4mm V = 20 kN Asked: Determine the location of…

Pressure and Stress