In the circuit shown V = 100 V, C1 =1µ F, R1=29.9 Kohm and %3D R2=100 Kohm. Find value of Vci at t=20msec. the switch is connected to a for long time and at t-0 is connected to b. ww8

Q: I+ Iェ-I,=0 R= 33052 生っ Lett: 6.98- luw I, -(00I; = 0 -(2) I. I, I3 Right : 15-330I2- lWT,=0 6.98V…

A: The giving circuit diagram is shown below, R1=100ΩR2=330Ω

Q: Known Vsat for LM741 ± 14V for source voltage Vs ± 15V. If Vi1 = 3 V and Vi2 = 4 V, Ri1 = Ri2 = Ro2…

A:

Q: j202 Select one: O a. None of these O b. Is 100 <-90° mA O c. Is = 5.0<.90° A 90° me ell

A:

Q: Consider the circuit shown below. Vcc VEE= 7V. R1 = 4k and R2 5k. B 99. Determine Ig in mA. %3D Vcc…

A:

Q: = Figure Q2 shows the exact equivalent circuit of a 50 Hz, 30 kVA, 2200 V/250 V single- phase…

A:

Q: V: 818 mV V(p-p): 0 V V(rms): 0 V V(dc): 818 mv V(freq): -- R1 A PR1 4.7kQ R2 36.8kQ: R3 10KQ V1 10V…

A:

Q: Solve for Ic of Figure 41. VCC T15V O 0.33mA O 4.77mA O 3.3mA O 0.477mA R1 $390KQ R2 $2.7kQ2 Q1 Beta…

A: Bipolar Junction transistor (BJT):- It is a three terminal  device that is Emitter, base and…

Q: plot the output voltage when the resister and capacitor in the series branch and the resister and…

A: Given that, Case 1: One resistor and capacitor are connected in series, and input voltage is changed…

Q: Shunt PMMC was designed by using indirect method to provide an ammeter with current range 5A, 10A,…

A:

Q: the cquivalat of the 302. What is the four Resistars Value of Ry %3D R3=452 Rz = ?

A: Please refer the attached images for the complete answer..

Q: If you want to convert a 2 V DC signal to 10 V DC signal, then the values of R, and R2 should be R…

A: Given circuit, Converting 2 V DC signal to 10 V DC signal, so vi=2 Vvo=10 V

Q: Subject to a step input, the voltage drop across the resistor took 696.3103us to reach 13% of its…

A: for study state , L gets short so  ,i = ViR  ,  V0=Vi As voltage drop across L is 0 at study…

Q: A circuit is used to clip a portion of its input waveform. The output waveform   a. can not be used…

A: A circuit is used to clip a portion of its input waveform. The output waveform

Q: Consider the circuit. Given hfe = 50, hie = 2000. Find voltage gain. * Vec 8k 20k O-279 10k 4k Vout

A:

Q: If you want to converta 2 V DC signal to 10 V DC signal, then the values of R, and Rz should be…

A: Virtual Ground: Virtual Ground concept is only applicable for ideal op-amp. For an ideal op-amp…

Q: For circuits as shown behind of paper let (VD = 0.7v, VBE(FA) = 0.7v, VBE(sat) = 0.8v, %3D %3D…

A:

Q: Find the values of Vr, Ic, Ir, C, & Zr. + VR - 35 ohms IR 7V 12V/60HZ Ic +

A: Given: In the given question they have mentioned an AC circuit with having capacitor, resistor and…

Q: Create a circuit and apply kirchhoffs laws

A:

Q: Design a defferenbator for gren input signul and find out the olp Voltage.

A:

Q: klst2) Sketch vi0ot Jocus and also G Is) HIS) = %3D S+25+6 detevimine W at K=1-33

A:

Q: Two resistors are connected in parallel with a total resistance of 50 Q and a total noise voltage of…

A: Please refer the attached images for the complete answer..

Q: In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L…

A:

Q: Why this happening to my circuit? I am inputting a 0-3.3 V sine wave into my voltage follower…

A: According to the question, we need to discuss the problem in the designed circuit for voltage drop…

Q: Node Voltage Method: To find V1 V1 – 0.56 V1 V1 Z1 Z2 = 0 Z3 + Z4 + Z5 V1 – 0.56 -1.457462849j V1 V1…

A: KCL states that algebraic sum of current at a node must be equal to zero. It is also called nodal…

Q: Find out the power of the following signal: x(n)=2ej3n Please show all the steps

A: For any discrete-time signal x(n), the power of the signal can be computed using the following…

Q: Subject: Fundamental of Electronics Question: Do Theoretical Calculation to get value for Vclipper

A: Note: All the circuits are named incorrectly. In the solution, we will use the correct names for the…

Q: In the circuit given in the figure, VT = 25mV, IVBEI = 0.7V, R1-999.39Kohm, R2 = 32.36Kohm, R3 =…

A:

Q: Q3/A- For the circuit shown in figure 3 draw the output voltage waveform across the SCR and the…

A: SCR: It is a semiconductor device from the thyristor family used as a switch. It is on when the gate…

Q: Using the appropriate curve, develop a linear equation for the output temperature as a function of…

A:

Q: Set up explains brief each bullet points phygics angument that. • Any wive has a non Zero res…

A: NO every wire have some resistance since wire have length and cross section area therefore wire must…

Q: 1- +10V LOK D EsV SV -10 V Diodes are IN914

A: Wave shopping circuits are of two types linear wave shaping circuits. Such circuit designs with…

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.