Find out the power of the following signal: x(n)=2ej3n Please show all the steps

Q: (i) Initial Output = %. (ii) Output after T1 Seconds = %. (iii)Output after T2 Seconds= %.

A:

Q: Determine V,, Vs(pk), Vupk), Vdc, PIV, and fout. Draw also the output waveform with the voltage…

A:

Q: If the four input lines of a multiplexer are DO, D1, D2 and D3, and the two select lines are given…

A: Four input lines of a multiplexer, and input for the select lines are 11 then find the output of…

Q: x(n) = aln , if a = 1/3, X is 1/3, x is %3D %3D an energy signal with E=0.25J O b. a power signal…

A: The given signal is an Energy signal.

Q: PROBLEMS 26. A system has a transfer function of 100/(s² + s + 100). What will be its natural…

A: 26)  Given a second order transfer function To find the natural frequency and damping ratio

Q: 1. Simulate the scenario shown in Figure 1.4 given in the above sections. Hint: continuous signals…

A: Given two sine signals with frequencies 40 and 90Hz Asked to sample and plot  the given signals at…

Q: Transition table: Present state Next state Output (Q, 02) (z) Input state(**2) 00 Input state (xx2)…

A:

Q: Answer the following Hexadecimal to decimal conversion problem: Convert the HEX NUMBER EF6F. 5324 to…

A:

Q: You need to produce a square wave with a low voltage of 0.500 volts and a high voltage of 2.500…

A:

Q: For the circuit shown in below, determine and sketch the output waveform signals: - Vini = 2 sin(wt)…

A:

Q: Problem 3: Please convert the Mealy FSM in Table 1 to a Moore machine by showing the Moore FSM…

A: A Mealy machine is a finite-state machine whose output values are determined by its current state as…

Q: write ALP to calcyate the ho. of ones and zeros in n an 8 but number

A: Let's load the 8 bit number into 2501h memory location and store the result in 2502h and 2503h Store…

Q: In a temperature measurement system, measured value is obtained as 145.3°C when the temperature…

A: Given:  Measured value Am=145.3 True value AT=224.3 Relative error= (Am-AT)/AT

Q: A schematic of a capacitive pressure converter is shown in the figure below. In this schematic, the…

A:

Q: Write a technical report on Darlington Pair, which include the following topics: a) Technical…

A: Since it is asked to solve from sub-part (a) to (c), so we are solving only the first three…

Q: EXEMRIE (1) Determine the output of the DAC in Figure (a) if the waveforms representing a sequence…

A:

Q: The Qooutput of the counter shown below FF0 FF1 FF2 Do D D2 CLK is present before Q1 or Q2 changes…

A: Let us suppose initial output from each flip flop is 0 i.e. QoQ1Q2 = 000. It is a type of…

Q: El/OD W=0 owing state-table ate Next state output z2zlz0 W=0 W=1 000 001 010 011

A:

Q: If the frequency of the input signal is 200 Hz, the frequency of the full-wave rectified signal…

A: The relation between the input and output frequencies for a full wave rectifier is given below:

Q: Find the Fourier Series of the function. f(x)= -K if -2<x<0 1-K k if 0<x<2 - A sinusoidal voltage &…

A: Solve the first question, unless the student has asked for a specific question to be solved, subject…

Q: If you want to convert a 2 V DC signal to 10 V DC signal, then the values of R1 and R2 should be

A: According to question: The gain of the op-amp is given as

Q: (a) State two differences in the features of a general-purpose computer application compared to an…

A: Since you have posted multiple different questions. we will solve the first question for you. To get…

Q: Shown in the figure is timing diagram of a T-FF. Using the timing diagram determine which type of…

A: Consider the given question;

Q: Figure 9 shows a 5 bits adder type DAC. If the shift registers s1 and s4 are ON, and the others are…

A: Given, 5-biy adder type DAC is  Vref= 10V Shift registers S1 and S4 are ON. Remaining all are OFF.…

Q: With the same circuits used in the picture below (Design J-K 4-bit Asynchronous Counter up/down)

A: The 4-bit asynchronous counter needs to be designed and the counter has to perform both up counter…

Q: 27-1: We want to design a state machine that follows the state transition table below: Prese Inpu…

A: Encoding the state: State table is given as:

Q: LVDT produces an rms output voltage of 5.0 V for displacement of 3.5 mm. Calculate the sensitivity…

A: We have been given an LVDT transducer which produces the, Output Voltage = 5.0 V Displacement = 3.5…

Q: In figure the values of Rx and Cx are Rp

A:

Q: C2 (i). Draw the Schematic diagram and explain the working of LVDT and write any two applications of…

A: Linear Variable Differential Transformer, LVDT is the most used inductive transducer for converting…

Q: 17. If a frequency modulator produces 4 kHz frequency deviation for a 10-Vp modulating signal,…

A:

Q: Derive the Sum of Minterms form of F and F'. Show all work. F(A, B,C,D) = A'B'C'D' + AD + A'C'D' +…

A: To derive the Sum of Minterms form of ( F ) and ( F' ), let's first express ( F ) and ( F' ) in…

Q: 3. XMM1 is an ammeter and its reading is OA for the whole input signal cycle. What could be wrong in…

A: The diodes are made of semiconductor materials. Silicon and germanium are common semiconductors for…

Q: 2. Discuss the following circuits by directly stating their circuit diagrams, waveforms, principle…

A:

Q: Draw an illustration of an open grinding circuit. Draw an illustration of a closed grinding circuit.

A: Open grinding circuit consisit of one or more than one friding mills which are either connected in…