Solve that In an experiment for a balanced "symmetrical" A-connected pure inductive load if the readings of one ammeter and one voltmeter are100 mArms and 10Vrms; respectively. Calculate the total/complex power and the power factor.VuO 0+j1.732 VA, and unityO O-j1 W, and unityO 1.732 VAr, and zero lagO 0+j3 VA, and zero lagO o-j3 VA, and zero lead

Given values are - VRMS=10VoltIRMS=100mAPure Inductive loadVRMS=10∠0oVoltIRMS=100∠-90omA Given load…

In an experiment for a balanced "symmetrical" A-connected pure inductive load if the readings of one ammeter and one voltmeter are 100 mArms and 10 Vrmsi respectively. Calculate the total/complex power and the power factor. Va Vu Vu O Otj1.732 VA, and unity O O-j1 W, and unity O 1.732 VAr, and zero lag B VA, and zero lag O O-j3 VA, and zero lead

In an experiment for a balanced "symmetrical" A-connected pure inductive load if the readings of one ammeter and one voltmeter are 100 mArms and 10 Vrmsi respectively. Calculate the total/complex power and the power factor. Va Vu Vu O Otj1.732 VA, and unity O O-j1 W, and unity O 1.732 VAr, and zero lag B VA, and zero lag O O-j3 VA, and zero lead

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Please read questions carefully i need power factor and Reactive power of load
Which cannot be said since Z is an inductive load in the circuit given below? A) load voltage period is 0.02sec. B) Load voltage peak value is 311V. C) Load voltage frequency is 50Hz D) Load voltage average value is 220V.
15. You are working on a power factor correction installation, and you notice with a clip-on ammeter as you add in capacitance the current drops, you add more capacitance and the current drops, you add more capacitance the current rises. How do you know when you are at unity power factor?
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
Assume that the load resistance can be varied between 0 and 4000 Ω andthat the capacitive reactance of the load can be varied between 0 and−2000 Ω. What settings of RL and XL transfer the most average powerto the load? What is the maximum average power that can be transferredunder these restrictions?
15 A of current is taken by a non-inductive load at 125 V. In order that the same current shall be generated from 240 V, 50 Hz mains. An inductor is now also then connected in series. Note: The resistance of the inductor should be ignored and also assume the waveform to be sinusoidal. Determine the phase difference between the current and the applied voltage, the impedance of the circuit and the inductance of the inductor.
Problem 1 • A sinusoidal source with frequency of 60 Hz and rms-voltage of 100 V is connected to an RL load of 10 ohms and 100 uH. Find Power Factor From Calculation Find Power Factor From Plot L=10mH find power factor from calculation only
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of 158 volts, 50 Hz supplies the combination. Determine the following: a. Circulating current b. Voltage across the resistor c. Voltage across the capacitor d. Real power supplied by the source e. Reactive power supplied by the source f. Apparent power of the circuit g. Power factor of the entire circuit
6. Determine the peak and average power delivered to RL in figure. 2:1 RL 220 N 120 V rms alll lelll
An inductive reactance of 6 ohm is connected in series with a parallel combination of a variable resistor R and a capacitive reactance of 15 ohm across 100V , 50 hz supply. a. Solve for the frequency so that the magnitude of the inductive reactance is 2 times the magnitude of capacitive reactance. b. Solve for the value of R so that the total current I will be maximum.
what will be the power factor, if the inductive reactance is equal to the capacitive reactance of 20 Q and the resistance is 20 Q. O a. Unity O b. Zero O c. Leading O d. Lagging
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms