Answered: Determine the complex power for the…

Determine the complex power for the following give values and specify whether the power factor is leading or lagging. Vrms = 220 V, P= 1 w, Z|= 20 k2 (inductive) B1

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: A balanced star-connected load as shown in the figure draws a total power of 12 kW. Calculate: i.…

A: In the power circuit, A 3 phase balance star load consumer total power = 12kW Finnd the phase…

Q: a. Find the average power delivered to each element. b. Find the reactive power for each element. c.…

A: The equivalent impedance of the circuit is: 1Z=1R2+1XL-1XC21Z=122+12π*50*4-2π*50*52Z=1.2Ω So, the…

Q: A residential four-wire system supplies power at220 V rms to the following single-phase…

A: (b) For first phase total load are – Since loads are bulb so that total power is real and reactive…

Q: C is ↑ 7.5 mH 12 Ω For the circuit shown above, what is the maximum average power that can be…

Q: 3. Refer to the circuit shown C 120V, 60HZ Z = 10+j12 2 (a)What is the power factor? (b) What is the…

Q: Problem 8: Calculate the apparent power, power factor, real power and reactive power associated with…

Q: QQAL 440 V rms 8 Þa two-terminal load draws 3 kVA of apparent power at a lagging power factor of…

A: Electric powerElectric power in DC circuits can be defined as voltage multiply by current. This…

Q: For the circuit show below, solve for the following: a. The complex power delivered to each passive…

Q: Q2. Calculate average, apparent, complex power delivered to the load Z, = 8+j6 ghm. Also estimate…

Q: A source supplies power to the following three loads connected in par- allel: (1) a lighting load…

A: The solution is given below

Q: 8 Ω -j2 N () 4/0 Α Ν

Q: Compute the reactive power for -j252 with a voltage source, Vg = 24020° (rms) 12.5 N 15 2 V, -j25 N…

A: In this question we will find reactive power in capacitor...

Q: Determine the power factor of the entire circuit below as seen by the source. Calculate the average…

A: In this question we need to find a input power factor and average power delivered by source.

Q: Problem 4: For the circuit shown in figure, compute the average power delivered to the load, the…

Q: 2. Find the value of reactive power in the system which draws a 10-A current having a power factor…

A: It is given that: I=10 Acosϕ=0.8 laggingV=250 V

Q: Example XL Determine the power factor and the true ll power (average power) in the shown circuit :…

A: given here a circuit and asked to calculate the power factor and average power. and given voltage is…

Q: a. Refer to the circuit is shown below (a) What is the power factor? (b) What is the average power…

Q: From the circuit, determine the value of load z for maximum power transfer and the maximum average…

Q: 69 9V ZL Sinusoidal voltage of RMS value 9 Volt is applied. Resistance value R = 12 ohm. Determine…

A: In this question we need to find a value of load impedance for maximum power transfer to load and…

Q: a) What is the value of Ro in ohms? b) Calculate the average power delivered to Ro. c) If Ro is…

Q: 18 10+j5 Rejf6 25 For the circuit shown below, Take Van = 100 Vrms and the transmission line…

A: solve prob..

Q: Calculate the average power þ Power Factor ww 8N N -jun 5010° deliverd by the 62 ww 11 fir source.

Q: A load of 500 kVA operates on 1100 V, 50 Hz mains with power factor of 0.6 lagging. It is required…

A: We have an load with, KVA rating = 500 KVA Vs = 1100 V Frequency (f) = 50 Hz Power factor (cosϕ1) =…

Q: ブ32 j2 Q 10/30° V 4 2

A: To delivered maximum power to the load in the AC circuit, Thevenin impedance should be conjugate to…

Q: Rține jXline L1 L2 L1: Absorbs an average power of 12kW at a leading power factor of 0.9. L2 :…

A: L1 : Absorbs an average power of 12kW at a leading power factor of 0.9. L2: Absorbs an apparent…

Q: In the circuit, determine: a) I, VR and VC in phasor form b) The total power factor, and indicate…

A: As per the guidelines of Bartley we supposed to answer first three subpart only.

Q: 3. Obtain the power factor of circuit.Specify the power factor as leading or lagging -j1N ww 10 j22…

Q: A generator is supplying a load of 500 kW at a power factor of 0.8 lagging. If the power factor is…

Q: If the voltage and current given below are suppliedby a source to a circuit or load, determinea. The…

A: Let the angle given be in radians. Find the complex power supplied by the source.

Q: The voltage at the terminals of a load is 250 V(rms). The load isabsorbing an average power of 40 kW…

A: the load complex power S is given by, S=P+jQ=40000-j30000 VAso,P=40000 WQ=-30000 VAR since the…

Q: For a load of Z = 50260° N with Irms = 100460° A, find the following: (a) complex power, S (b)…

Q: 2. For the network shown in the figure and the applied source: lic + IR i, = 5 x 10-3 sin(377t –…

A: We will apply KCL at upper node and get: iR+iL+iC=iSe3kΩ+ej4kΩ+e-j2kΩ=5∠-20°…

Q: Question NO: 1 Consider the network as shown in figure Q1. Determine the load impedance ZL for…

A: From Maximum Power Transfer Thereom

Q: f a 425 sin (wt + 45o) V supplies a current of 60 cos(wt - 350) A, Determine the power in the…

A: Given data, Voltage us given, V=425sinωt+450 Current is given I=60cosωt-600 A Current can be written…

Q: An alternator is supplying a load of 300 kW at a power factor of 0.6 lagging. If the power factor is…

A: Given, Active power rating, P1 = 300 kW Power factor, cosϕ1 = 0.6 lagging At power factor, cosϕ2=1…

Q: a) A 140-V rms, 60-Hz source is applied to a load impedance Z. The apparent power entering the load…

Q: In the circuit below, Z1 = 10L-10 and Z2 = 10L15. If the source voltage is 310coswt, calculate the…

A: In the circuit, Two loads are connected in parallel of the voltage source. Find the apparent…

Q: A 110-V rms, 60-Hz source is applied to a load impedance Z. The apparent power entering the load is…

Q: Referring to the figure below, the 60-N resistor absorbs an average power of 240 W. (a) Calculate…

Q: For the circuit shown, what is the complex power, S, consumed by the 18 + j32 load impedance?…

A: Given circuit: Load impedance, ZL=18+j32 Ω

Q: 4. In a system with P = 80 kW and Q = 30 KVAR. Determine the power factor.

A: given p and q

Q: If the rms values of voltage and current are 120 V and e A. The instantaneous power is, (a) 120/2…

A: Input =rms =120 V rms current =e-j20=1∠-300Imax=2∠-300 V=1202cosωt+00 Instantaneous power is given…

Q: Rjine jXiine + + VL |L, L2 - L1: Absorbs an average power of 20kW at a leading power factor of 0.9.…

Q: 80 -j2 n 4<0° A -j3 0 50 j20 10<30° V

Q: For the circuit show below, solve for the following: a. The complex power delivered to each passive…

Q: Find the complex power supplied by the source and the power factor of the source for the network…

Q: For the circuit shown below, find the average power delivered to the circuit and the power factor of…

A: Power factor is the ratio of useful power to the total apparent power. It tells how much power of…

Q: 16. Find the value of impedance which absorbs a complex power of 2300 VA with a 30 degrees angle at…

Q: 2. For the circuit show below, solve for the following: a. The complex power delivered to each…

A: Complex Power: Complex power is defined in terms of angle as compared to apparent power which is…

Q: i)Evaluate the total impedance, average power, reactive power, and power factor in the provided…

Concept explainers

Sinusoids And Phasors

Sinusoids are defined as the mathematical waveforms that are used to describe the nature of periodic oscillations.

Circuit Theory

Electric circuits are a network that comprises of a closed-loop, which helps in providing a return path for the current through a switch. When the switch is activated, the load operates, and the current accepts a path to finish the circuit at a low potential level from the opposing high potential level. Electric circuits theory is a linear analysis that helps in establishing a linear relation of voltage and current for R (resistance), L (inductance), and C (capacitance).

Question

100%

Determine the complex power for the following give values and specify whether the power factor is
leading or lagging.
Vrms = 220 V, P = 1 W, Z| = 20 k2 (inductive)
B1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
15 A of current is taken by a non-inductive load at 125 V. In order that the same current shall be generated from 240 V, 50 Hz mains. An inductor is now also then connected in series. Note: The resistance of the inductor should be ignored and also assume the waveform to be sinusoidal. Determine the phase difference between the current and the applied voltage, the impedance of the circuit and the inductance of the inductor.
Q2. For the circuit shown below, sketch the current waveforms iş and io and determine the Average and RMS for both currents. a = 50° TI 50 2 Vs = 300 sin 100zt ( cot T2 in cot
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. ot io Vs = 220V a = 220° + ot 1002
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. a = 50° T1 50 2 ot Vs = 300 sin 100rt T2 ot
Power factor is leading if a. load absorbing reactive power Ob. load is inductive C. voltage lags current d. voltage leads current Clear my choice
Need asap pls help. Solve for the voltages across and currents through each component. Show the complete solution and explain. The total power should be zero..
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
For figure (1)draw and calculate the voltages waveform across each half of secondary winding and across load when 100sin2π60t applied across the primary, then find PIV.
Which cannot be said since Z is an inductive load in the circuit given below? A) load voltage period is 0.02sec. B) Load voltage peak value is 311V. C) Load voltage frequency is 50Hz D) Load voltage average value is 220V.
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707