In a tensile test, a test piece of 25 mm diameter is tested over a gauge length of 125 mm The elongation over this length is 0.0875 mm under a pull of 68725 N. In a torsion test, a test piece was made of the same material and of same diameter, and it twisted 0.025 radians over a length of 250 mm at a torque of 0.3068 kN-m. Find Poisson's ratio and the three elastic modulis of the test piece material

In a tensile test, a test piece of 25 mm diameter is tested over a gauge length of 125 mm The elongation over this length is 0.0875 mm under a pull of 68725 N. In a torsion test, a test piece was made of the same material and of same diameter, and it twisted 0.025 radians over a length of 250 mm at a torque of 0.3068 kN-m. Find Poisson's ratio and the three elastic modulis of the test piece material

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.4P: A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
O49 In a tensile test, a test piece of 25 mm diameter is tested over a gauge length of 125 mm. Tme elongation over this length is 0.0875 mm under a pull of 68.725 N. In a torsion test, a test piece was made of the same material and of same diameter and it twisted 0.025 rad. Over a length of 250 mm at a torque of 0.3068 kNm. Flnd Poisson's ratio and three elastic modulii of the test piece material.
A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter db / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gb = 28 Gpa.
A drill rod with a diameter of 1/2 in. is made of high-strength steel alloy with a shear modulus of 11.6 * 106 psi. The rod is to be subjected to a torque T.What is the minimum required length L of the rod so that the cross section at one end can be rotated 60° with respect to the other end without exceeding an allowable shear stress of 45 * 103 psi?
In a tensile test, a test piece of 25 mm diameter is tested over a gauge length of 125 mm. The elongation over this length is 0.0875 mm under a pull of 68,725 N. In a torsion test, a test piece was made of the same material and of same diameter and it twisted 0.025 rad. Over a length of 250 mm at a torque of 0.3068 kNm. Find Poisson's ratio and three elastic modulii of the test piece material.
A test piece is cut from a brass bar and subjected to a tensile test. With a load of 6.4 kN the test piece, ofdiameter 11.28 mm, extends by 0.04 mm over a gauge length of 50 mm. Determine:(i) the stress, (ii) the strain, (iii) the modulus of elasticity.(b) A spacer is turned from the same bar. The spacer has a diameter of 28 mm and a length of 250 mm, bothmeasurements being made at 20~ The temperature of the spacer is then increased to 100~ the natural expansionbeing entirely prevented. Taking the coefficient of linear expansion to be 18 x 10-6/~ determine:(i) the stress in the spacer, (ii) the compressive load on the spacer.rC.G.] [64 MN/m 2, 0.0008, 80 GN/m 2, 115.2 MN/m 2, 71 kN.] Could you please answer the parts after the first three? If you use * could you please explain what you mean by it! Thank You :)
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm? A = 400mm? A - 200mm 40KN 10KN 20KN 2.5m 2.0m 1.5m
A test conducted on a steel bar whose cross section is 0.5 in. by 4 in. is performed. Anaxial load of P = 30,500 lb. produced a deformation of 0.00103 in. over a gauge lengthof 2 in. and a decrease of 0.000078 in. in the 0.5-in. thickness of the bar. Determinea. Poisson’s ratio,b. the elastic modulusc. the decrease in the 4-in. cross-sectional dimension.
The modulus of elasticity of mild steel is equal to .. .? .... .. a. 2 x 10ʻN/m? a. 2 x 10'N/m 2 b. 2 x 10° N/m 4 c. 2 x 10 N/mm 5 d. 2 x 10 N/mm Check
An alloy steel specimen of 30 mm diameter with a gauge length of 200 mm is load tested. It has extension of 0.16 mm under a load of 85 kN. Load at elastic limit is 160 kN. Young's modulus of the specimen in GPa O 127 O 143 O 150 O 172