In a multibyte addition program, when must you use the ADD instruction? When must you use the ADC instruction?
Q: 1. The bit sequence 1101 is serially entered (right-most bit first) into a 4-bit parallel out shift…
A: [1] Consider a four bit shift register Q3 Q2 Q1 Q0 Given, Initially the register is clear, Q3 =0, Q2…
Q: How many bits are required for the control selector in the 64x1 multiplexer? a. 4 O b. 5 О с. 6 How…
A: Use fundamental of multiplexer design 1)Option c 6 2)Option c 8
Q: How many bits are needed to represent decimal values ranging from 0 to 10000?
A: The number system is used to represent information in digital electronics. Different bases exist in…
Q: b) What is the purpose (jll ) of the parity bit during data transmission?
A: According to the question we have to discuss the purpose of the parity bit during the data…
Q: Specify the number of registers in a 5K memory chip?
A: As we know that 1Kb has 1024 bytes 1 Kb=1024 bytes
Q: B) Consider register A contains 11101100 . What is the register value after performing mask…
A: to consider register A contains 11101100. what is the register value after performing mask operation…
Q: Describe two major difference between JMP instruction and a conditional jump instruction.
A:
Q: A common bus system which is capable of transferring 2 bits at time with number of registers are 4…
A: The circuit diagram for a common bus system which is capable of transferring 2 bits at a time with…
Q: 7. What type of register can have a complete binary number loaded into it in one operation, and then…
A: Note as there are several questions and we are asked to solve one question at a time. So do mention…
Q: The serial adder required ten clock pulses to add two, five bit binary numbers. (True or false. if…
A: According to question: The answer is false because in serial adder for addition of two 'N' bit…
Q: 1-Why do we use DPSK? For the following message 1111000101110 give the DPSK system. (Note the…
A: DPSK
Q: After execution the far jump instruction: JMP A3000127h; the new value of Physical Address=A3127h.…
A:
Q: Explain any five instructions with examples from data transfer group instruction?
A: The instruction is a binary pattern, which is designed inside a microprocessor to perform a…
Q: What is the purpose of the Mux in a 1-bit Register?
A: Purpose of the Mux in a 1-bit register
Q: Binary to Octal Decoder using 7-Segment Display. write the k-map and use 4 input and 7output?
A: Truth Table digit A B C D a b c d e f g 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 1 1 0 0 1 1 1 1 2 0…
Q: 1- Discus the results in all steps. 2 - What is the variation in the address decoder circuit if its…
A: what is the variation of address decoder circuit if it deals with memory what is the variation of…
Q: Show the status of PSW (Program status word) after addition of two 8bit numbers 26H and 3FH. Also…
A: As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again. The…
Q: How many bits are needed to count up to 255 in binary?
A: From the counters in digital electronics
Q: 1- Explain the operation of the PCM encoder used in module ED-2960F. 2- Discuss the advantages and…
A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: How to store (1050000)10 in register $s0? Write down the instructions that stores the data in $s0…
A:
Q: A large multiplexer 512 to 1 require how many address line?
A: The number of address lines in a MUX is the addition of select lines and input lines.
Q: 7. (15') Stack: What is the function of the stack? If the current values in the stack segment…
A: According to the question, we need to define stack and also find the addresses of Bottom of Stack…
Q: What would be the value of ESP after pushing the 32-bit value shown below onto the stack? 000000A5
A: Before PUSH instruction, ESP value is =0001000
Q: Load the number of ffh into the 'a' register and write the code that reduces the number in the 'a'…
A: Load the number of ffh into the 'a' register and write the code that reduces the number in the 'a'…
Q: 3. A 12-bit Hamming codeword containing 8 bits of data and 4 parity bits is read from memory. What…
A: To show the procedure of hamming
Q: dont use others answers show your work step by step short answer Suppose we are given the…
A:
Q: DISCUSSION: 1- Is the Gray code arithmetic code? Why? Where this code used? 2- What is the parity…
A: Need to find about gray codes and parity bit Note:- as per our guideline we are supposed to answer…
Q: For the given diagram determine which of the inputs devices is transferring its data to the data Bus…
A: Figure shows that input channels are connected to microprocessor through 3 state octal buffer
Q: A) How many Binary digits do you need to represent a deciaml number 355?
A: The binary digits system consists of only two numbers i.e., 0 and 1. In order to find the number of…
Q: The binary number 1010 0011 is an ?even or odd? number that has ?even or odd? parity?
A: If the number of ones are even then it is a even parity If the number of ones present in the…
Q: Write a Verilog code for 8-bit up/down counter for any type of Modeling.
A:
Q: Q4. Suppose we receive a bit sequence: 00000 00100 11110 10000, and suppose a repetition code with 5…
A: In the received bit sequence a repetition code with 5 total bits and 1 data bit is used that implies…
Q: 1) Assume the signals with the highest amplitude of 5 volt are transmitted. The max error is about 1…
A: The solution is given below
Q: Refer to the following registers values and memory snippet to answer the following questions.…
A: The 8086 microprocessor is a 16 bit microprocessor with 16 data lines and 20 address lines. It is…
Q: Q4. A common bus system which is capable of transferring 2 bits at time with number of registers are…
A: Multiplexer- A multiplexer is a device that is used to select one of several input signals and send…
Q: Byte Addressable Instruction Memory:
A: CODE:-
Q: Write the contents of the first two addresses of ram in two lines after running the given code.
A: According to the question, we need to find the contents of the first two addresses of ram in two…
Q: The processor has performed the following addition operation: 0x01A0 + 0xC410 ------ 0xC5B0 What…
A: The signed 16-bit number in decimal can have either positive or negative sign. Let us consider for…
Q: Explain what the stack pointer register is and what it does in a few words.
A:
Q: What are the contents of the file registers WREG, 0x010, 0x020, 0x410, 0x420, after the following…
A: After the execution of the program, the registers will be having the following values
Q: In a DPCM system, the number of bits per sample is 7. How many levels are present in the quantizer?
A: A quantizer is an integral part of a differential pulse code modulated (DPCM) system. The number of…
Q: SV What is clocking block ? what is program block?
A: Reg is driven by always block it can't be driven by continuous assignment statement. Always block…
Q: Question 1 (a) Sketch and describe the programming model of the 68k MPU. (b) At one given fime, how…
A: Solution (a) - The 68k MPU's programming model is also known as the Instruction Set Architecture.…
Q: Look at the following parts of the program PROCESS (enable) BEGIN IF (enable'EVENT AND enable - '1')…
A: Because of statement Process (enable) statement written below this will execute only whenever enable…
Q: 10. Use 4-bit binary addition to perform 6 + 11. You must first convert the decimal number into…
A: We have to add two decimal numbers, 6 & 11, by using 4-bit binary addition. As, first we have to…
Q: 1- Identify the addressing mode for: MOV CX, [1234] 2-The instruction that subtracts 1 from the…
A: In this 1st question , we have to determine addressing mode ...and in 2nd question , we have to find…
Q: Q6) What is the smallest value ofn in linear block code with a minimum distance of three and a…
A:
In a multibyte addition program, when must you use the ADD instruction? When must you use the ADC instruction?
Step by step
Solved in 2 steps
- the diagram on the right is for a register bank circuit that contain 8 registers. Each register is 16-bit. Theregister can read or write to one register at a time using address bus.Design the circuit and specify the width of EVERY bus...The instruction SUB AX, BX, gives the result of ... In register. Explain the given question with an example. Not just copy paste answer.Solve the following question. You must show your work. a) What does 962F000016 represent in an IEEE single-precision floating-point number? b) Convert -151o to a 16-bit sign-magnitude representation. c) Convert-151o to a 16-bit two's complement representation. d) Define the system status register value after an instruction execution resulted the following: a. Result was a non-zero value, a negative value, had a carry and extended bits. b. Trace mode was not on and was executed in supervisor mode. C. Any higher interrupt priorities higher than level 3 will be recognized.
- An 8051 subroutine is shown below: SUB: RO, #20H @RO , #0 MOV LOOP: MOV INC RO CJNE RO, #80H, LOOP RET a. What does this subroutine do? b. In how many machine cycles does each instruction execute? How many bytes long is each instruction? C. d. Convert the subroutine to machine language. e. How long does this' subroutine take to execute? (Assume 12 MExplain the arithmetic operations in binary number system and how code conversion is done between binary and decimal numbers.Write a Verilog code for 8-bit up/down counter for any type of Modeling.
- 1. Write down 2- differences between Von-Neumann and Harvard architecture. 2. you are executing an instruction, SUB $s0, $s1, $s2 (address 0x20). Draw the datapath of this instruction when $s1=10, $s2=5. When are the stages in this datapath? Mark the components which are active in corresponding stages. 3. How to store(1050000)10 in register $s0? Write down the instructions that stores the data in $s0 register.8085 microprocessor went through its manipulation operation in the ALU, the results was transferred on the data bus and status of the results was stored in the flag register for indications . With your knowledge and understanding illustrate a complete bit configuration of 8085 flag register and show the functions of the represented bits in the register.Write a program in assembly language to toggle PORTB 400 times. Use BNZ instruction.
- When an XIC instruction is cleared: a. This enables the next instruction (the rung-condition-out is true). b. This disables the next instruction (the rung-condition-out is false). c. The rung-condition-out is not scanned. d. The rung-condition-out is has to have an OTL.Consider the following assembly program MOV CX, 1100H DLY: SUBS CX, CX, #1 NOP BNE DLY NXT: --- (a) How many times does the BNE DLY instruction get executed? (b) Change the first line of the program so that BNE DLY is executed 34 times (c) Change the second line of the program so that BNE DLY is executed 34 times, while the fist line stays unchanged (MOV CX, 1100H)- The stack memory is addressed by a combination of the plus offset. The PUSH and POP instructions always transfer between segment -bit number the stack and a register or memory location in the 8086 microprocessors. For string instructions, DI always addresses data in the segment. The 8086 LOOP instruction decrements register for a 0 to decide if a jump occurs and tests it