In a belt transmission dynamometer, the driving pulley rotates at 400 rpm. The distance between the centre of the driving pulley and dead mass is 820 mm. The diameter of each driving as well as intermediate pulleys is equal to 360 mm. Find the value of the dead mass required to maintain the lever in the horizontal position, when the power transmitted is 5 kW. Also find its value when the belt just begins to slip on the driving pulley. u being 0.25 and maximum tension in the belt 1500 N.

In a belt transmission dynamometer, the driving pulley rotates at 400 rpm. The distance between the centre of the driving pulley and dead mass is 820 mm. The diameter of each driving as well as intermediate pulleys is equal to 360 mm. Find the value of the dead mass required to maintain the lever in the horizontal position, when the power transmitted is 5 kW. Also find its value when the belt just begins to slip on the driving pulley. u being 0.25 and maximum tension in the belt 1500 N.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
QsI The whel of mutuv Cy cle and the engine parts have antoncent •f inertia 2-5 kgm? and o I5 ky.m respectively The axis of rotation of the engine erant Shaft is parallel to thatof the road wheels-IR the gear ratio is 5:1 and the diameter o f the road whels is o5m, find the magnitude anal divection . f the gyroscopic Couple when the motor Cycle rounds a Curve of 3om radius at 16 mls.
An engine develops 200 kW of power at a mean speed of 75 rpm. The coefficient of energy fluctuation is 0.15 and speed fluctuates within ±3% of the mean speed. Find the moment of inertia of the flywheel that must attached to the crankshaft of the engine in order to maintain the speedwithin the acceptable range.
2. A 75 kW induction motor runs at 740 rpm in clockwise direction. A 19 tooth helical pinion with20 degree normal pressure angle, 10 mm normal module and a helix angle of 23 degree is keyed to the motor shaft. Draw a 3-dimensional sketch of the motor shaft and the pinion. Show the forces acting on the pinion and the bearing at A and B. The thrust should be taken out at A All dimensions are in mm y 750 B 200 Z2=38 Z₁ = 19 X
4 A compressor requires 120 kW to run at 240 rpm from an electric motor of speed 750 rpm by means of a V-belt drivę. The diaincter of comp shaft pulley should not be more than 1000 mm while the center distance between the shafts is 2000 mm. Belt speed should not be more than 25 m/sec. Detcrmine number of belts to transmit the power it each belt has cross-sectional arca of 375 mm', density 1000 kg/m' and allowable tensile stress of 2.5 MPa. The pulley groove angle is 40° and coeff, of friction between pulley and belt is 0.25:
A multi plate friction clutch is used to transmit the power from the engine to a rotor which has a mass of 152 kg and a radius of gyration of 0.34 m. The inner and outer radius of the clutch disc is 0.055 m and 0.217 m respectively. The clutch plate has 4 contact surfaces (n = 4) and the axial thrust is 379 N. The flywheel of the engine rotates constantly at 1,106 rpm. Calculate the time required to accelerate the rotor from rest if the clutch is suddenly engaged. Take u = 0.42. Assume uniform wear in clutch.
A multi plate friction clutch is used to transmit the power from the engine to a rotor which has a mass of 152 kg and a radius of gyration of 0.34 m. The inner and outer radius of the clutch disc is 0.055 m and 0.217 m respectively. The clutch plate has 4 contact surfaces (n = 4) and the axial thrust is 379 N. The flywheel of the engine rotates constantly at 1,106 rpm. Calculate the time required to accelerate the rotor from rest if the clutch is suddenly engaged. Take μ = 0.42. Assume uniform wear in clutch.
P5/ The wheel of metor Cycle and the engine parts have antoment of inertia 2-5 kg.m? and o 15 Kg.m² respectively The axis of rotation of the engine erank Shaft is parallel to that of the road wheels-If the gear ratio is 5:1 and the diameter o f the read whels is o.65 m, find the magnitude and direction of the gyroscopic Couple when the motor Cycle rounds a eurve of Bom radius at l6 m/s.
A 500 pound weight is attached to a cable that is being lifted by a 10 inch diameter drum. The 48V DC motor selected has a no-load angular velocity of 800 RPM and a stall torque of 500 inch-pounds. A gearbox has been designed to spin the drum as quickly as possible. Assume that there are no friction losses in this system. The drum is driven by a 72-tooth gear with a diametral pitch of P=8, and is 3D printed such that it has a yield strength in shear of τy = 2500 psi. Assuming that the entire output torque required to turn the drum is produced by the force on one tooth, and that the gear tooth would fail by being sheared off at the pitch circle, determine the required gear face width, b, for a factor of safety of 3. Note that circular tooth thickness, t, at the pitch circle is π / (2P). Repeat for a gear made out of 6061 Aluminum (σy = 35 ksi, τy = 20 ksi). Only do the part for the 6061 gear do not do it for the 3D printed gear
A1. A flat belt drive for speed reduction has pulley diameters of 200 mm and 380 mm. Themaximum belt tension is not to exceed 620 N and it is required to transmit 1·8 kW at anoutput speed of 360 rev/min. Determine:(a) The input torque. (b) The belt speed. (c) The limiting slack side tension. (d) The initial tension at which the belt should be set.
A motor drive has three different loads, first is rotational motion and coupled directly to the motor with the torque of 3 Nm. Second a rotational load is connected to the first load through a reduction gear with the ratio of 1:4. This load has a moment of inertia of 12 kg.m² and torque of 8 Nm. The third load is connected to the second rotational load that has a translational motion and consists of 1250 kg weight to be lifted up at a uniform speed of 115 meter per-minutes. The gear and translational system have efficiency of 85% and 90%, respectively. At this condition, the motor has an inertia of 0.3 kg.m² runs at a constant speed of 1350 rpm. If the transmission losses are neglected, (i) draw and label the block diagram to represent the drive system. (ii) calculate the equivalent inertia referred to the motor shaft. (iii) determine the total developed torque from the motor. (iv) examine the developed power from the motor.
A 7,5 kW electric motor (star-delta start) running at the speed of 900 r/min is to drive a laundry machine, which operates 12 hours per day, by means of a simplex chain drive. The laundry machine must run at approximately speed of 308 r/min. Based on the space restrictions, the center-line distance is limited to 400 mm. Specify the length of chain (in mm) to be used as well as the exact center-line distance. Note that the form of lubrication used is TPYE 2.