If V1 = 18 V, V2 = -9 V, R1 = 1.2 kOhm, R2 = 4.7 kOhm, R3 = 2.4 kOhm, and all V. diodes are silicon for the circuit below, the output voltage Vo is equal to No need for a solution. Just write your numeric answer in the space provided. Round off your answer to 2 decimal places. R1 D1 V1 - Si D2 D3 R2 R3 - V2 Si Si Vo

If V1 = 18 V, V2 = -9 V, R1 = 1.2 kOhm, R2 = 4.7 kOhm, R3 = 2.4 kOhm, and all V. diodes are silicon for the circuit below, the output voltage Vo is equal to No need for a solution. Just write your numeric answer in the space provided. Round off your answer to 2 decimal places. R1 D1 V1 - Si D2 D3 R2 R3 - V2 Si Si Vo

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2/A- What are the types of rectifiers? with diagrams. B- (1) Show the voltage waveforms across each half of the secondary winding and across RL when a 100 V peak sine wave is applied to the primary winding in Figure.2. (2) What minimum PIV rating must the diodes have? 940001 +100 V- V OV -100 V î A 2:1 00000 eebee Fig.2 D₁ ✈ IN4001 D₂ IN4001 ellel 00000 R₂ 10 kf
4. Determine Vout for the figure below when the types of diodes (Si) and the resistance (R₂) equal 20.2. 1 V 2 V- 3 V + 2 ΚΩ www 2 ΚΩ + V out
Given the following circuit in Figure 1, determine whether the Diode is ww 5K2 conducting or not. You need to assume both cases. Firstly, assume that the Diode is ip conducting and do the needed calculations, then assume that it is not conducting and do the A needed calculations. Also, you need to show your drawing on how the circuit is changed in 10 K 2 1000 2 both cases. 20 V Vin The first assumption with needed calculations 15 V The second assumption with needed calculations The drawing in both cases
Please fill the table below. Vp = 0.7V for both diodes. 1. State which diode is on. 2. Replace the diodes with their model 3. Determine Vo and I for the different input voltages (A and B) given in the table below. Show all your work. D1 A. B DI D3 Vo Si 3 2 A O Si vo D2 4 IIKO 6 v
Determine the current though and voltage across all of the diodes shown in Figure 1.Assume constant voltage drop model for each of the diodes. { X = 7 & Y= 8 }
D3 太 10 K The diodes in the circuit are Silicon with forward voltage of 0.7 V. Fill up the table showing the state, voltage and current of each of the diodes. Show how you validated the state of each diode. Follow the reference shown in determining whether the diode voltages and currents are positive or negative. 8K 5 V 1K 1 mA Diode State VD ip + Vp - D1 D2 D3
Calculate the current flowing through the given circuit and the voltage value at the V0 ends. (Threshold voltage = 0.3V for Germanium diodes, Threshold voltage for silicon diodes = 0.6V)
1. Using first approximation, find the voltages across resistance. 2. Using second approximation, find the currents across Si diodes
4. Determine Vout for the figure below when the types of diodes (Si) and the resistance (R) equal 20.. + Vout www + 1 V 2 V 3 V 2 ΚΩ 2 ΚΩ
Current 420 ohm 30 V 1,(max) = 80 mA Voltage Vp-in 2.2 kohm Vp-out 0.6 V Zener Current Answer the following question according to the above. Remember Kirchhoff's laws when making your calculations in this question. According to the given graph, how many volts is the voltage value on it when this Zener diode is on a flat supply?
Plz answer correctly ....
15