Answered: If a load absord 20KVA at the leading…

Engineering

Electrical Engineering

If a load absord 20KVA at the leading power factor of 0.6 Write the complex form of power

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.8P: Consider the circuit shown in Figure 2.23 in time domain. Convert the entire circuit into phasor...

See similar textbooks

Related questions

Q: A single-phase electrical load draws 1000KVA at 0.6 power factor lagging Find the real and reactive…

A: Given, A single phase load draws, S=100 kVA Power factor, cosϕ=0.6 lagging

Q: A power station has a maximum demand of 40 MW. The total load connected to the station is 100 MW. If…

A: We have been given an power station with, Maximum Demand = 40 MW Average Demand = 25 MW Connected…

Q: (a) the full load efficiency at unity power factor;

Q: For the circuit show below, solve for the following: a. The complex power delivered to each passive…

Q: Find power factor of given circuit ww 30/0° V rms -j20 4 2

A: Given circuit,

Q: Give the value of the impedance seen across the nodes x and y when w = 1000rad/sec.

Q: Determine the complex power for the following give values and specify whether the power factor is…

Q: (b) Three loads are connected in parallel to a 240Z0° V rms of 50 Hz source. Load 1 absorbs 90 kW…

A: The detailed solution is provided below.

Q: The average real power delivered by the current | = 3 - j4 A to the impedance Z = 10 - j5 N is:…

A: I=3-j4 AZ=10-j5 ohm

Q: For the given network diagram find the complex power and power factor supplied by the source. 0.1Ω…

Q: A load operates at a voltage of Vx = 475 V−rms and absorbs P = 56 and Q = 23 VAR of power. Use this…

Q: 2. Find the value of reactive power in the system which draws a 10-A current having a power factor…

A: It is given that: I=10 Acosϕ=0.8 laggingV=250 V

Q: An industrial load with a power factor of 0.707 lagging. If the voltage across the load is 98<0.…

Q: Find the impedance of a 600 n generator terminal impedance if the voltage 6 volt rms and the current…

Q: Discuss the following term in reactive circuit? a) Real power b) Apparent power G) Power factor 1.

Q: The average load of a dairy plant at 11 kV, 50 Hz is 950 kW at 80 percent power factor but the…

A: The circuit this is excited the use of alternating supply is referred to as an AC Circuit. The…

Q: Given the following Thevenin equivalent circuit. We connected ZL and its value is chosen to maximize…

Q: The load current at which maximum efficiency occurs is independent of the load power factor. Select…

A: We need to find The load current at which maximum efficiency occurs is independent of the load…

Q: For the circuit shown in figure Calculate (a) the power factor (b) the average power delivered…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: For the circuit shown: a) Find Z1 & Yı. b) Find I1, I2, and I3. c) Find the power factor, the real…

A: Disclaimer: Since you have asked multipart questions, we will solve the first three subpart for…

Q: Vs 18 V pk RL 220 N (a)

Q: The daily demands of three consumers are given below in KW: Plot the load curve and find (1) maximum…

A: The solution can be achieved as follows.

Q: BA series-connected load draws a current i(t) = 4 cos(315t + 10°) A when the applied voltage is v(t)…

A: According to question we have to calculate the value of Apparent power, power factor and value of…

Q: (d) The branch current (in both polar and Cartesian forms): I= (e) The branch current (in both polar…

Q: Find the power delivered by the source. B)Find the reactive power delivered by the source. C)Find…

Q: Solve for the equivalent impedance and admittance seen at the source. Solve for is(t).

Q: For a load of Z = 50260° N with Irms = 100460° A, find the following: (a) complex power, S (b)…

Q: Q4) By using the circuit given below; a) of the system. b) c) d) Find the total value of active…

A: Active Power(P): The power which is deployed and absorbed by the electric circuit to do some useful…

Q: Find the total impedance, total current drawn by the system, total power (apparent) delivered by the…

Q: Two electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the…

A: The solution can be achieved as follows.

Q: E is 120 V. Load 1 is 1 kW resistive, load 2 is 400 W resistive and load 3 is a 1 HP motor that is…

A: Given data, Load 1 is resistive with 1 KW Load 2 is resistive with 400 W Load 3 input power is 1 HP…

Q: If the apparent power of a source is known, then the power factor, active and reactive powers can be…

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: Q3: For the circuit shown below, If I 4435° Ams, determine the average power being supplied: (a) by…

A: Disclaimer: Since you have asked multipart questions, we will solve the first three subpart for…

Q: For the system shown, (a) find the average/real power Pg and reactive power Qs supplied by the…

A: Given system has parameters as: Load 1- Q1=100VAR, P1=200W, Load 2- Q2=100VAR, P2=200W, Load 3-…

Q: An alternator is supplying a load of 300 kW at a power factor of 0.6 lagging. If the power factor is…

A: Given, Active power rating, P1 = 300 kW Power factor, cosϕ1 = 0.6 lagging At power factor, cosϕ2=1…

Q: Problem 4 An electric saw, a wood shaper, and a motor load of a workshop establish a 18 kVA power…

Q: a) A 140-V rms, 60-Hz source is applied to a load impedance Z. The apparent power entering the load…

Q: 62 30/0° V rms -j22 Determine the power factor of the entire circuit of as seen by the source.

A: Power factor is the ratio of true power by apparent power. The value of power factor lies in between…

Q: When connected to 230 V (rms) ,50 Hz power line, a load absorbs 4 kW at a lagging power factor of…

Q: Calculate the real power P, reactive power Q and apparent power S, include units and show…

Q: For the circuit show below, solve for the following: a. The complex power delivered to each passive…

Q: For the circuit shown below, find the average power delivered to the circuit and the power factor of…

A: Power factor is the ratio of useful power to the total apparent power. It tells how much power of…

Q: In the circuit shown below, find the complex power supplied by the source and the source power…

A: In given circuit three loads are connected in parallel. Voltage will be same across each load but…

Q: Determine the complex power for the following give values and specify whether the power factor is…

Q: A factory has an electrical load of 1600kW at a lagging power factor of 0.8. An additional variable…

Q: 2. For the circuit show below, solve for the following: a. The complex power delivered to each…

A: Complex Power: Complex power is defined in terms of angle as compared to apparent power which is…

Q: For the circuit below with two sinusoidal voltage sources at = 7000 rad/sec, determine the impedance…

Q: i)Evaluate the total impedance, average power, reactive power, and power factor in the provided…

Q: An electric load consists of a resistor, a capacitor and an inductor connected in series. The total…

A: As per guidelines i have to answer first three sub parts only please post remaining again

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

100%

If a load absord 20KVA at the leading power factor of 0.6 Write the complex form of power

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
Convert the following instantaneous currents to phasors, using cos(t) as the reference. Give your answers in both rectangular and polar form. (a) i(t)=5002cos(t30) (b) i(t)=4sin(t+30) (c) i(t)=5cos(t15)+42sin(t+30)
Given the complex numbers A1=630 and A2=4+j5, (a) convert A1 to rectangular form: (b) convert A2 to polar and exponential form: (c) calculate A3=(A1+A2), giving your answer in polar form: (d) calculate A4=A1A2, giving your answer in rectangular form: (e) calculate A5=A1/(A2*) giving your answer in exponential form.
A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the positive terminal of the source. Determine the real and reactive power and state whether the source is delivering or absorbing each.
An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is 1000 W. Determine (a) the real power absorbed by each of the impedances and (b) the source current.
Consider the circuit shown in Figure 2.23 in time domain. Convert the entire circuit into phasor domain.
Please read questions carefully i need power factor and Reactive power of load
Normally, the power factor of a load is improved by connecting a capacitor or inductor in series with the load. Select one: O True False
A 75MW power plant has an average load of 35000kW and a load factor of 65%. Find the reserved carried over and above peak load