Answered: Identify the part not belonging to…

Engineering

Mechanical Engineering

Identify the part not belonging to micrometer. Frame Ratchet Locknut Clamp

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.1: Understanding Drawings

Problem 10RQ: List and briefly describe the three types of tolerances used on prints.

See similar textbooks

Related questions

Q: It is a small tool that features the standard angle (600) for lathe centers and for threading tool…

A: Option c is correct.

Q: It is a widely use tool for laying out squaring and checking work.It consists is a square head and a…

A: following is the answer to the above question-

Q: What is the name of the size, bigger which should not be the size of a suitable work- piece? 1) the…

A: To select the correct option

Q: what is the measured distance to the nearest eigthth between the outside corners of the tongue and…

A: FRAMING SQUARE A framing square, also known as a steel or carpenter square, can be the most…

Q: If the main scale reading (mm) and vernier scale reading (division) are 27 and 47 respectively for a…

A: Given: main scale reading = 27mm vernier scale division = 47 division total division on vernier…

Q: If the main scale reading(mm) and vernier scale reading (division) are 29 and 18 respectively for a…

A: Solution:

Q: In transition fit, tolerance zone of hole is entirely above that of shaft tolerance zones of hole…

Q: If the main scale reading (mm) and vernier scale reading (division) are 49 and 10 respectively for a…

Q: Try square is a measuring tool used to measure the straightness and squareness of a workpiece.…

A: The square of the measure consists of two main elements, the blade, often referred to as a beam or…

Q: èstion 14 With respect to Fitting shop, which of the following tools is different from the other…

A: Given :- estion 14 With respect to Fitting shop, which of the following tools is different from the…

Q: The depth measurement is done by ___________________part of a Vernier Caliper. Ratchet Anvil Spindle…

Q: om a point or ravelled by t pressed in 4

A: given:bridge locateed 44.8m above the watert=2sec

Q: The taper on the lathe spindle is: A) 1 in 10 B) 1 in 20 C) 1 in 15 D) 1 in 25

A: The taper on the lathe spindle is 1 in 20.

Q: Describe two scales in Vernier Caliper?

A: Vernier caliper instrument is mainly used for taking accurate linear measurements. Vernier caliper…

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: 12 mm wrench fit over the head of a bolt that is 1/2" across

A: Given: Wrench size =12 mm Bolt size =1/2" AF (across the flat) To determine: Whether the wrench is…

Q: 9) To obtain a guide for centering irregular shaped workpiece in the lathe, its face should be laid…

Q: During operating lathe machine, the tool bit should be fixed as short as possible. Select one: True…

A: The given statement is true.

Q: 46. During the drill operations, the work piece and drill bit make an angle of 450. Select one: O…

A: Drilling is a cutting operation which uses drill bit to cut a circular hole in solid materials.

Q: ___________ tool is used for verifying the flatness of the component. A. Protractor…

A: Protractor is a device used to measure the angles. Engineers square is a checking tool which is used…

Q: Give at least 5 purpose of cutting internal threads by the use of Lathe Machine

A: given; Give at least 5 purpose of cutting internal threads by the use of Lathe Machine.

Q: 1000 rpm

A: 5) 104.72rad/s 6) 16.67s 7) 91.89N/m

Q: The tool used for marking center is __________. a. Steel rule b. Divider c.…

A: Solution:

Q: The ratio of Number of teeth to pitch circle diameter is called

A: (1) Module: It is the fraction of the diameter d of pitch circle to the number of the teeth T of the…

Q: with proper value

Q: Describe and sketch open drill jigs with its components

A: Open type jig , in which the top plate is arrange to swing about a fulcrum point , so that it is…

Q: List three rules to follow when using or storing semi-precision measuring tools.

A: Semi precision tools are used for the measurement of the various dimensions of the workpiece.

Q: Is the 'fit' between the 2 parts shown below a clearance fit or interference fit?

Q: of drill

Q: For a No. 7 ball bearing, the New Departure Handbook states that the maximum bore should be 1.3780…

Q: platform weighing machine

A: From very early times, civilizations used weighing machines in business transactions. Over the…

Q: In uptight drill machine, the power is transmitted from electric motor to spindle with help of belt…

A: Drilling machine is a mechanical equipment used to introduce holes into a specimen which are in…

Q: If the main scale reading(mm) and vernier scale reading (division) are 16 and 9 respectively for a…

A: Least Count of vernier=(1/20)=0.05mm as a vernier caliper with 20 division on the vernier scale

Q: equal par machine is

Q: volume of metal

A: Given; While cooling a cubical catsing of side, 40 mmVolume shrinkage=3%, 4% and 5% liquid state…

Q: Countersinking process is carried out by using twist Drilll. O True O False

Q: When removing or installing bearing, where should force be applied

A: The application of force during installation or removal of bearing is one of the critical factors,…

Q: Centre punch is a marking tool used in workshops for the purpose of making indentations on the…

A: Center punch is a point tool having a metal rod with a conical edge at its one end for creating an…

Q: IDENTIFICATION 1. It is a hardened steal instrument having parallel rows of cutting edged or teeth…

A: 1. File- it is a cutting tool with hardened cutting edges in parallel configuration. It is use in…

Q: ifferentiate 3 types of lathe machine in terms o

A: Lathe machine: Lathe machine has a chuck and the toolpost, Chuck is used to holding the workpiece…

Q: Show the steps and calculations to determine one type of fit. Diameter of ball bearing hole is =…

Q: In drilling operation on lathe machine, the drill bit is fixed in _______. a. Tool post b. Carriage…

A: Ans_ D_ Tailstock

Q: Applying finger pressure on the belt near the pulley end is not the correct method to check the…

A: The 'thumb test' method in which a finger is pressed onto the belt to check whether the belt has…

Q: e allowable position tolerance that may be applied to each part in a

A: Determine The applied allowable position tolerance

Q: With respect to a fitting operation, which of the following is the correct sequence of events? O A.…

A: The sequence of events in the fitting operation are first measurement is done to find the dimensions…

Q: Write any two difference between preventive and breakdown maintenance, with any one advantage and…

A: Preventive maintenance recognizes any issues some time recently equipment disappointment or…

Q: Right the accuracy in millimete

A: The screw gauge with a micrometer. The micrometer screw gauge is used to measure dimensions that are…

Q: The line used to show where a section view is cut is called A. a section line B. a hatch line…

A: An engineering drawing is a type of technical drawing which is used by thee industries to convey…

Q: If the deflections of the drive belt of a lathe machine exceeds 8 mm tensioners are used for…

A: If the deflections of the drive belt of a lathe machine exceeds 8 mm tensioners are used for…

Q: A metric thread of pitch 2 mm and thread angle 60° is inspected for its pitch diameter using 3 wire…

A: Given:Pitch, P=2 mmThread angle, 2θ=60oθ=30o

Concept explainers

Limits, Fits, and Tolerances

The maximum or minimum allowable sizes within which the size of component lies are known as limits. The limits are classified into two types:

Question

Identify the part not belonging to micrometer.

Frame

Ratchet

Locknut

Clamp

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve show all steps/solution as well
Solve using parallelogram and Trigonometry please explain how
stion 18 If the main scale reading(mm) and vernier scale reading (division) are 16 and 9 respectively for a vernier caliper with 20 division on the vernier scale. yet rered Find Final reading in mm = ed out of ag question O Tyne here to search
When no geometric tolerance is specified, the size tolerance controls the well as the size. O form orientation O profile O position as
answerquickly
16q A slip gauge setting height of 65.215mm is observed and an angle of 480 is found during the precise angle measurement of a workpiece in a workshop. Find the length of the Sine Bar used in mm= (Enter at-least 4 digits after decimal points)
List and briefly describe the three types of tolerances used on prints.
Suppose that the length of the steel bar is measured by a number of different observers and following set of 11 measurements is recorded as set A (units mm): 398, 420, 394, 416, 404, 408, 400, 420, 396, 413, 330. Next the measurements are taken using different ruler to produce measurement set B: 409, 406, 402, 407, 405, 404, 407, 404, 407, 407, 408. It can be shown that the mean values set A and B are 409 and 406 respectively. Which of the two measurement sets A and B, and the corresponding mean value, should have most confidence in? why? Text
Test-II. Write down all the operations or step by step procedure on how to create the object below. Write down also the name of the machines and the tools that you will use to complete the drawing below. 824 020 015 22 15 35 40 100 NOTE: ALL DIMENSIONS ARE IN MM ALL CHAMFERS ARE 1X 45
On the part in Q1, show the size and shape of the tolerances zone. Lecture 5 Q1 On the part below, apply position controls to allow the holes to move 0.2mm radially. Include references to datum features A, B and C.
1s 4 part
Draw front and top view of the following isometric drawing of a bushed bearing. All dimensions in mm. Scale 1:1.