IDENTIFY THE FF: AIRCONDITIONING AND VENTILATION 1. Acts as a master controller which keeps the system in automatic operation 2. Adds heat to a fluid 3. Ratio of the actual partial pressure of the water vapor in a space to the saturation pressure of pure water at the same temperature. 4. Also known as the heat content of air-vapor mixture 5. Temperature as read on an ordinary temperature 6. Temperature where in water will start to condense 7. Equipment that removes heat 8. Is the process of treating air 9. Their purpose is to create atmospheric conditions favorable to human health, comfort and efficiency. 10. The system is to maintain indoor conditions for winter season

IDENTIFY THE FF: AIRCONDITIONING AND VENTILATION 1. Acts as a master controller which keeps the system in automatic operation 2. Adds heat to a fluid 3. Ratio of the actual partial pressure of the water vapor in a space to the saturation pressure of pure water at the same temperature. 4. Also known as the heat content of air-vapor mixture 5. Temperature as read on an ordinary temperature 6. Temperature where in water will start to condense 7. Equipment that removes heat 8. Is the process of treating air 9. Their purpose is to create atmospheric conditions favorable to human health, comfort and efficiency. 10. The system is to maintain indoor conditions for winter season

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 15RQ: Why is information regarding the specific volume of gases important to the designer of...

See similar textbooks

Similar questions

Why is information regarding the specific volume of gases important to the designer of air-conditioning, heating, and refrigeration equipment?
Define a near-azeotropic refrigerant blend, and give twoexamples.
PLEASE DO NOT USE PSYCHROMETRIC CHART. THANK YOU In the diagram below inlet air is drawn over a pool of liquid water in a steady-state, steady-flow isobaric process. Evaporation on the pool resultsin saturated air at the exit. The pool of liquid water is assumed to be at the same temperature as the exitair. Discharge fans at the exit provide a volumetric flow rate of 800,000 ft3/min. Problem #2: Assume that the R134a chiller is turned off such that Qout = 0, but the evaporative coolersystem continues to operate. Determine:a) The exit temperature, T2 (°F)b) The mass flow rate dry air through the system (lbm/sec).c) The rate of liquid water resupply required for continuous operation (lbm/hour).
Q.1. A refrigeration process with interstage cooling uses refrigerant HFC-134a, and the outlet of the condenser is to be saturated liquid at 40°C. Refer to the following figure for stream numbers in your solution. The pressure of the flash chamber and the intermediate pressure between compressors is to be 290 kPa. The evaporator is to operate at -20°C and the outlet is to be saturated vapor. The flowrate of stream 1 is 23 kg/h. The flash chamber may be considered adiabatic. The compressors may be considered to be 80% efficient. a) What is the power input required to the first compressor? b) What are the flowrates of streams 6 and 7? What is the enthalpy of stream 4? Hot Side 6 5 Condenser 2nd Stage Compressor Throttle Valve 7 Flash Chamber Vapor Phase Only 1st Stage Compressor 8 Throttle Valve Evaporator 1 2 Cold Side
| Part of a refrigeration system operates at steady state with Refrigerant 22 as shown in the figure below. There is no significant heat transfer to or from the heat exchanger, valve, and piping. Kinetic and potential energy effects are negligible. State 1 is a saturated liquid. What temperature is it, in °F? Describe the refrigerant at state 4 as one of the following: compressed liquid, saturated liquid, tyro-phase mixture, saturated vapor, or superheated vapor. Determine the required mass flow for the given operating conditions, in lb/min. Determine the rate of heat transfer between the evaporator and its surroundings, in b. Btu/min. Make sure to clearly state the direction of heat transfer. 1. T=10°F P= 15 Ibf in (AV), = 9.5 ft/min. Pi= 120 Ibf/in.? Heat exchanger Throttling valve Evaporator P 15 lbfin.2 X3 = 1.0 P2= 15 lbf/in.2
O Falge QUESTION 2 The refrigerant undergoes a change of phase during the heat-transfer process, the pressure of the retrigerant is the saturation pressure during the low supply and low rejection processes. True False QUESTION 3 Frequently, the vapor of the liquid leaving the condenser is lower than the saturation temperature. O True False QUESTION & The pressure of the iquid leaveng the condenser we be less than the pressure of the vapor entarng, wd etempernd the retigerant in the condenser. O Te QUESTION S Are many situations in which it is desirable to combine three cycles in series, either power systems or refigertion sytems, to take advantage of a very wide temperature range or to utilize what would otherwise be waste heat to improve etficiency O true O False QUESTION 6 A cycle can't be made very efficient, since the temperature differences between the two fluid streams can be controlled through careful design of the combined system. True
Completely solve and provide the diagram. Box the final answer. Write legibly 4. A single effect water evaporator operating at 125 kPa abs vapor pressure. Motive steam is available for evaporation at 1.0 MPa with 90% vapor content, what is the mean temperature difference?
A summer air-conditioning shown below is required to maintain a certain room at specified conditions. The layout of the system is indicated on the next page and the specifications are listed below.System specifications:Required room temperature: 23⁰C, 50% Relative humidityAtmospheric pressure: 101 kPaOutside air conditions: 30⁰C, 80% Relative humidity Sensible heat gain: 5 kWLatent heat gain: 4 kWTemperature rise across fan: 1.5⁰CTemperature of air leaving cooler: 12⁰CTemperature of air entering room: 18⁰CApparatus dew point of cooler: 7⁰C
QI: An R-134a refrigeration system produces 10 ton of refrigerating effect at the evaporating temperature -10°C and the condensing temperature of 40°C.The absolute pressure measured at the inlet and outlet of evaporator are 2.0 bar and 1.7 bar, respectively. Considering there are no superheat and sub cooling effects, calculate the following parameters with or without a drop of pressure in the evaporator: (i) Refrigerating effect (ii) Mass flow rate (iii) Power requirement in kW/TR (iv) COP
The thermocouple couldn't be directly used for temperature measurement, unless a reference point is defined. This reference point is: Select one: O a. The boiling temperature. b. All of the above. c. The ambient temperature. d. The mixture of ice-water temperature.
A summer air-conditioning shown below is required to maintain a certain room at specified conditions. The layout of the system is indicated on the next page and the specifications are listed below.System specifications:Required room temperature: 23⁰C, 50% Relative humidityAtmospheric pressure: 101 kPaOutside air conditions: 30⁰C, 80% Relative humiditySensible heat gain: 5 kWLatent heat gain: 4 kWTemperature rise across fan: 1.5⁰CTemperature of air leaving cooler: 12⁰CTemperature of air entering room: 18⁰CApparatus dew point of cooler: 7⁰C Draw the processes on a psychrometric chart and determine the following: 1.The ratio of mass flow rate of re-circulated air to the mass flow rate of air supplied to the room. 2.The heat removed by the cooling coil.3.The heat supplied in the re-heating coil. 4.The cooling coil bypass factor.
A steam boiler has the following data: - Steam output: 8000 lb/hr - Steam pressure: 135 psia - % moisture: 1% - Feedwater temperature: 120 F - Boiler Surface Area: 1330 ft2 Determine: a. Factor of evaporation b. Equivalent evaporation c. Boiler horsepower d. Boiler rating