I need quick handwritten solution. (1)A ball of mass 1000 kg is tied to an elastic cable of Steel of Elasticity Modulus 210 GPa and diameter of 1 cm and length 20 cm. When the ball is lifted using the cable, determine the stretch in the cable assuming that all deformation remain within elastic limit.

I need quick handwritten solution. (1)A ball of mass 1000 kg is tied to an elastic cable of Steel of Elasticity Modulus 210 GPa and diameter of 1 cm and length 20 cm. When the ball is lifted using the cable, determine the stretch in the cable assuming that all deformation remain within elastic limit.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A sample of silicone breast implant, polydimethylsiloxane (PDMS), is placed under unconfined compression. The magnitudes of the resulting longitudinal and transverse strains have been measured to be 2.7 and 1.341, respectively. The young's modulus of the implant is 500 kPa. Calculate the shear and bulk moduli.
A beam of length 4m and flexural stiffness (EI) of 1.4 x10 Nm², is simply supported at its ends as shown in Fig. Q3. The beam is subjected to a concentrated load of 20 kN at a distance 1m and a clockwise couple of 15 kNm applied in the plane of bending at a distance of 3m, both measured from the left end. (i) (ii) (iii) RA A 1m 20KN B 3m 15kNm I O D RD Fig. Q3: Loaded structural beam Calculate the reaction forces at the two end supports. Macaulay's approach is to be used to find slopes and deflections along the beam. Write the general expression for the bending moment at a section X-X at distance x measured from the left end to enable the solution. Using 'double integration method', derive an expression for the vertical deflection along the beam; hence determine the vertical deflection at mid-span.
Determine the instantaneous stress and elongation of a 30 mm diameter bar if a mass of 60 kg falls through a height of 60 mm on to a collar which is rigidly attached to the bottom end of the bar as shown in Figure Q2. The bar is 1.2 m long and is suspended vertically. The Modulus of elasticity, E, for the material of bar is 210 GPa. Take g = 10 m/s2.
Kindly include short explanation. View image.
For the prismatic bar in simple tension shown below, the stress state at any point "M" is characterized by Sig = p, and the other stress components are null. You are asked to determine the stress vector, as well as its normal and shear components, on a generic facet of normal parallel to the xy plane.
A mass of 45 kg falls freely from a height of 2,5 m onto a collar fixed to the bottom end of a vertical steel rod. The rod is 20 mm in diameter and 8 m long. Calculate (a) the instantaneous stress induced in the rod; (b) the instantaneous elongation of the rod; and (c) the strain energy stored in the rod (E = 205 GPa).
H.W 1 A6 m long hollow bar of circular section has 140 mm diameter for a length of 4 m, while it has 120 mm diameter for a length of 2 m. The bore diameter is 80 mm throughout as shown in Fig. B 140 80 300 kN + 300 kN 80 120 4 m 2 m Find the elongation of the bar, when it is subjected to an axial tensile force of 300 kN. Take modulus of elasticity for the bar material as 200 GPa.
Help
A cylinder with a piston diameter of 100 mm under apressure of 20 MPa exerts a force on the left end of a lever. Calculate the force obtained at the end of the lever? Answer: 40,000kN
An enormous and expensive artwork with mass 42.8 kg is mounted on a wall with four heavy-duty steel bolts, each with a diameter of 5 mm. There is 10 cm gap between the painting and the wall. The shear modulus of the steel bolt is 9.0 x 10^10 N/‘m^2. Find the shear stress on the bolts and find the resulting vertical deflection of the bolts.
A same circular plate with thickness of h-190mm is considered here again. The plate made from a material which its Young's modules and Poisson's ratio are E=60 GPa and V-0.22, respectively. Workout the value of flexural stiffness D in GN.m (GN.m3 10° N.m) (Hint: round your answer 4 digits after decimal point))? Ro
A metal rod is 50 mm in diameter and 1.3 m long. The rod has a collar on one end and is suspended vertically. The height through which this load may fall if the instantaneous stress is limited to 90 MPa is 1.71870× 10−3 m. The value of Young modulus is 132.40 GPa. 2.1 Calculate an extension when a weight of 30 kN is suddenly lowered onto the collar.2.2 Calculate the force required to cause the maximum stress.