Kindly include short explanation.View image. 2. A steel tape having a cross-sectional area of 0.06 cm? and a modulus of elasticity of 2.0 x10° kg/cm?, weighs 0.03 kg/m. Its length is 30.00 meter when standardized at a pull of 5 kg andsupported throughout its length. Determine the tension at which the effect of sag will beeliminated by the elongation of the tape due to increased tension.

Answered: Image /qna-images/answer/d913eeb7-f9a8-40cd-89a1-0fda93c0abd5.jpg

Answered: 2. A steel tape having a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Compound axial member ABC has a uniform diameter of d = 1.0 in. Segment (1) is an aluminum [E1 = 10,000 ksi] alloy and segment (2) is a copper [E2 = 17,000 ksi] alloy. The lengths of segments (1) and (2) are L1 = 66 in. and L2 = 110 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.45 in. L1 L2 (1) A d Aluminum (2) В Соpper Answer: kips P = i
Compound axial member ABC has a uniform diameter of d = 2.9 in. Segment (1) is an aluminum [E₁ = 10,000 ksi] alloy and segment (2) is a copper [E₂ = 17,000 ksi] alloy. The lengths of segments (1) and (2) are L₁ = 80 in. and L₂ = 110 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.10 in. A Li (1) Aluminum B L2 (2) Copper
Compound axial member ABC has a uniform diameter of d = 2.9 in. Segment (1) is an aluminum [E₁ = 10,000 ksi] alloy and segment (2) is a copper [E₂ = 17,000 ksi] alloy. The lengths of segments (1) and (2) are L₁ = 90 in. and L₂ = 130 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.30 in. L₁ P L2 Aluminum B Copper CP A Answer: P= i kips
Please show complete solution and box the final answer
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
A steel rod is 0.02-m in diameter and 2.5-m in length. The modulus of elasticity ofthis material is 210 GPa. The change in length afterapplying a tensile force of 150 kN is?
A bar, 12 mm in diameter is acted upon by an axial load of 20 kN. The change in diameter is measured as 0.03 mm. DeterminePoisson’s ratioYoung’s modulusBulk modulus Assume modulus of rigidity as 80 GPa
A concentric helical spring is used to support a load of 90 KN. The inner spring has arate of 495.8 KN/m and outside spring is 126.5 KN/m. If initially the inner spring is 25mm shorter than the outer spring, find the percent load carried by the inner spring. The correct answer is 76.81%. I just need the solution for this answer, thank you!
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If the Poisson’ Ration is 0.30 and the modulus of elasticity is 29xksi, determine the deformations at each direction. Also, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
The armor shown supports loads of 3 KN. The horizontal elements are 713cm long each. Determine the axial force on element FE; Use the section method to determine the axial force in the FE element and check your result with the nodal or joint method. INFO: Y= 100 cm
Please answer the problem. Provide a FREE BODY DIAGRAM. Show the FULL, COMPLETE and CLEAR solution.
Show all working explaining detailly each step.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS