I have a drawing layout with a standard ( correct drawn) marking consisting of two concentric circles and to right a trapezoid lying on its side this indicates A. 1 angle projection is used B. 3 angle projection is used C. isometric projection is used D. orthogonal projection

Q: rection: Locate the center of gravity in figures A & B by putting a dot or a point in each of the…

A: centre of garvity is the point where the gravitational force is acting through

Q: Given the top and front view create a section view.

A: Find Create a section view using the given top and front views.

Q: Draw the top view  front view  right side view  on graphing paper please. Put measurents if…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: draw the left side

A:

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the y-axis (θy)? Note that…

A: The cosine angle between two vectors  is as followes,

Q: What are the two dimensions that are not placed on the field of a drawing? A zero and a 45 degree…

A: The following things needs to be mentioned on the field of drawing: ◆ The diameter or radius of…

Q: Add the vectors using triangle rule or parallelogram rule

A: Draw the diagram of the vector system.

Q: The object shows the center of the whole is three inches from the left surface and one inch from the…

A: we have to determine what kind of dimensions are used in the hole

Q: The front and top views are given. Use this to create the missing side view. Note the front view is…

A: The required missing side view for A and B and the missing lines for C are drawn below.

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: Draw the top view  front view  right side view  on graphing paper please. Put measurents if…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: The given figure shows a casted I shape made from steel. You are required to design a wooden pattern…

A: According to the details provided in the question, we need to create a pattern with steel. First, we…

Q: Relative angles provide more information about segment position than absolute angles Select one:…

A: Given Data : Relative angles Absolute angles

Q: Given the front, top and side views of the drawing add the missing lines (center, object, and…

A:

Q: Exercise 6.2. Label the drawing that is attached. 1. Create datum plane A on the right hand face in…

A: All the required steps of the mentioned problem are done in the image below.

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the z-axis (θz)? Note that…

A:

Q: Which option is wrong?   a)The center head is used to find the center of a square on surface of…

A: Which option is wrong ?

Q: 1. Nominal surface the surface that represents the desired specifications on a part drawing nominal…

A: The measurement of small-scale differences in the height of a physical surface is known as…

Q: In the principle moments exercise, the algebraic sum of clockwise moment is not equal to algebraic…

A: We have to In the principle moments exercise, the algebraic sum of clockwise moment is not equal to…

Q: y Side 3 Side 1 8.0 Side 4 Side 2

A: Plz mention what to do?

Q: The headless type of set screw are known as screws * ....... grub O machine O rag О Сар The only…

A: Isometric drawing is the three-dimensional drawing of the object. It has two types - 1. Isometric…

Q: A 5 cm line segment makes an angle of 30 degrees with the vertical in space. It appears in true size…

A: Given: A 5 cm line segment makes an angle of 30 degrees with the vertical in space To find: To plot…

Q: The Answer is cut off on the right side.

A:

Q: Problem 2: Values: FA = 20 N FB = 30 N a = 25° Use the graphical method to determine... a) the…

A:

Q: 3- The plane in the space is determined by three points that are not on straightening one O right…

A: Explanation: 3) A plane in space is determined by three points that are not in straight line.  For…

Q: What is Line G?

A: Solution:

Q: Draw the top view  front view  right side view  on graphing paper please. Put measurents if…

A: Required Front view, Top view and Right Hand Side view are drawn using First Angle Method of…

Q: Divider tool is used for marking arcs in marking layout activity Select one

A: Divider is a tool with two point sharp metal points.

Q: Draw figure (3) by using circle, polyline, loft, slice and union.

A:

Q: Lab Activity 5H Calculating Radius End Points on a Lathe Part Use the illustration provided to…

A:

Q: C O C

A: Given: Hatching: Differentiates the areas that are cut and those areas that are not cut by the…

Q: two? a. 90 b. 70 30 d.15 5. Which line type is thick and black? a. visible line b. center line c.…

A: 4. Answer is b=70 Because of if A. 90=60+30 C. 30=30 D.15=45-30  But in B. 70=? Only angle can't…

Q: PLease draw the top view and section view with dimension of the figure

A: Here is Top View and Section View of figure with well dimensioned.

Q: 20 35

A: Projection of given drawings are drawn in 3D modelling software and solutions are provided in image.…

Q: 1. A field measures 10 x 15 cm (W x L) at 100cm SSD. What is the field size measurement at 128 cm…

A: In first field measurement, write the given data. W1=10 cmL1=15 cmSSD1=100 cmSSD2=128 cm

Q: I have three parts that I need answered pertaining to the print provided below.   This part features…

A: The angle between the center plane of each slot is 90o. Hence, the option (d) is correct.

Q: Below are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: Note: As per the policy, we can solve the first question from the multiple question. Please,…

Q: Partition the given figure and find the x and y coordinates.

A: Task at hand is to find the centroid of the shape in the figure

Q: Question 3) The length L is given as L=34 m on the plate in the figure. According to this; Question…

A:

Q: Sketch the OBLIQUE drawings based on the ORTHOGRAPHIC views.

A: Given :

Q: How do you draw both triangles?

A:

Q: Given the top and front view create a section view.

A: Given: The top and front view, To create a section view.

Q: 66. Which line type is used to indicate the outer form or the edges of the object? Select one:…

A: Solution:

Q: y is the angle an absolute value?

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.