How do you calculate the braking force of the bike?

Q: b) If all axles must be operational for the vehicle to function and the reliabilities are measured…

A: In this system it is impossible to run a vehicle without any tire so in this case each tire is in…

Q: While thinking about torques on a balanced a seesaw with two kids sitting at its ends, a student…

A: The wrong with the sketch is that the arrows representing forces on the seesaw are of equal length.

Q: what is the disadvantage of dynamic brakes when compared to mechanical brakes?

A: Mechanical brakes uses the application of friction in order to slow the vehicle or completely stop…

Q: Calculate the brake power produced by petrol engine if it running at 5000 rpm and having torque of…

A:

Q: a V-belt depends on the rotational speed of the smaller pulley.

A: In belt drive power transmission depends on following factors 1 linear velocity of velt 2 tension of…

Q: The free-body diagram of the brake arm is Your answer is incorrect - see feedback below. 1 6 in. 12…

A: According to the given data  A brake arm is provided with a circular drum We need to find The…

Q: A 4.8 m long from fixed point, 0.5 m wide and assumed a thickness of 30 mm throughout a springboard…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Explain about mechanical, hydraulic and pneumatic brakes

A: To explain: Mechanical, hydraulic and pneumatic brakes.

Q: A single cylinder, 4-ströke with a rope brake. The diameter of the brake s 600 mm and the rope…

A: GIVEN:effective break diameter D=600+26=626mmRPM N=450rpmdead weight w=200NSpring balance reading…

Q: A single block brake, as shown, has a tangential braking force of 2500 N and normal force of 9000 N…

A:

Q: : o Which control surfaces are controlled by the FACS

A: Hi and thanks for the question. Since you have asked multiple questions, we will solve the first…

Q: ##L2Q9 Explain the optimal braking balance, assign values to the equation in the Fx1/Fx2 ratio, and…

A:

Q: caliper failed due to static load or cyclic load?

A: Brake calipers is failed due to cyclic load.

Q: The following is an observation made during a trial on a 4-stroke diesel engine. The engine absorbs…

A: Given question is related to thermodynamics and IC engines.   Since you have posted a question with…

Q: The coordinate direction angle between the force acting on point A and the z axis is? (include units…

A:

Q: There is 465 psi in the hydraulic system that is powering a caliper with two pistons on each side of…

A: The normal force exerted by the caliper on the rotor can be determined as,

Q: 1- Does increasing the contact angle between the belt and pulley affect the amount of friction…

A: Belt and Pulley system is used to transmit power from one shaft to another shaft. In this mechanism…

Q: A car model has the following tires: front with code 235/35ZR19 and rear with code 305/30ZR19.…

A: To determine the sidewall height and diameter of the tires, we need to understand what the numbers…

Q: 5 ft 2 ft 7 ft The train has a weight of 23000 Ib and a center of gravity at G. It is suspended from…

A: Free Body Diagram for the given condition can be made as shown below: All normal reactions are…

Q: Question- 4 The following illustration shows the construction parts of the drum brake. From the…

A:

Q: is necessary to start the system of blocks moving to the right? The coefficient of friction is 0.10…

A:

Q: what are the 10 objects that have the application of moment couple that can found at home?

A: The moment couple acts on any object if two equal and parallel forces (in opposite direction) are…

Q: What is likely to happen if tyres of a different rolling diameter are used on the front and rear of…

A: Questions: What is likely to happen if tyres of a different rolling diameter are used on the front…

Q: TRUE OR FALSE 1. The primary and secondary suspensions are designed to achieve very poor ride…

A: 1. False They are designed to achieve very good ride quality 2. True they are connected through…

Q: What is the different between on-road bike accommodations and off-road bike accommodations?

A: This question is based on the concept of on road and off road bikes.

Q: Where is the highest value for the brake thermal efficiency and the lowest value for the specific…

A: Figure shows the variation of brake specific fuel consumption and brake thermal efficiency of a high…

Q: 6. What is the total potential energy for the system shown * R Flywheel m 1 1 v = k(x - 0) v =k(x –…

A: Potential energy: The energy stored by the system that depends upon the relative position of system…

Q: 1. The product of the force and time interval (when time interval is very short) is known as impulse…

A: This question is based on the concept of Mechanics. As per the guidelines we are subjected to solve…

Q: Disc brakes are not as likely to fade during heavy braking as are drum brakes. True OR False?

A: Given Data : Disc Brakes  Drum Brakes

Q: Describe the operation of pneumatic suspension including shock-absorbers

A: Air/Pneumatic Suspension System:As Pneumatic systems are basically using incompressible gas/air. By…

Q: Discuss the types of brakes along with their figures. Compare disc and drum brakes by discussing…

A: Classification of Brakes   1.On the basis of Power Source   Mechanical braking system Hydraulic…

Q: LECTURE 14 vehicle with mass of 1900 kg traveled with speed of 78 on a level road surface, the…

A:

Q: Using the coefficients of static friction indicated, determine the largest vertical force P which…

A: To find: Largest Force P that can be applied to cord without causing motion

Q: (a) Define the meaning of static balance and dynamic balance.

A: Concept: Static Balance: 1)In this type of balancing, the body is at rest.  2) In order to balance…

Q: muscles 1. State the class of lever of each device below. load force fulcrum Туре2 Туре? Туре? Туре?

A:

Q: Write a short technical notes on the different tractions used in India?

A: Given question:   Write a short technical notes on the different tractions used in India?…

Q: What are various types of brakes?

A: Given The type of brake

Q: A strain gauge is glued to a structure. It has a gauge factor of 2.1 and a resistance of 120.2 Q.…

A: given dataguage factor=2.1resistance (R)=120.2Ωchange in resistance (△R)=120.25Ω-120.2Ω=0.05ΩE=205…

Q: Explain why the leading brake shoe wears quicker than the trailing shoe.

A: Leading brake shoe wears quicker than the trailing shoe. The leading brake shoe is also called…

Q: 752 SECTION 8 Brakes To practice using these principles, complete the following activity. Calculate…

A: Given question: Can someone help me with calculations for input/output force/distance for pistons in…

Q: Sind the weight of the pully te Kep the system in equilibrium. 65N 60 3.

A:

Q: Derivation of the relationship between tensile strength, contact angle and friction coefficient of a…

A: