Explain about mechanical, hydraulic and pneumatic brakes

Q: A block-brake shown below has a face width of 300 mm and a mean coefficient of friction of 0.25. For…

A: Given:Coefficient of friction(μ)=0.25Activating force(F)=400 N

Q: Describe the differences between radial and bias tires, citing the advantages, disadvantages, and…

A: The objective of this question is to understand the differences between radial and bias tires,…

Q: b) If all axles must be operational for the vehicle to function and the reliabilities are measured…

A: In this system it is impossible to run a vehicle without any tire so in this case each tire is in…

Q: what is the disadvantage of dynamic brakes when compared to mechanical brakes?

A: Mechanical brakes uses the application of friction in order to slow the vehicle or completely stop…

Q: An ABS modulates brake pressure. What does this mean

A: In normal braking system when we apply brakes then the wheel gets locked and wheel starts skidding.

Q: circuit diagram of

A:

Q: What's the similarity,  advantage and disadvantage between hydraulic system and pneumatic system?

A:

Q: (1)The brake mean effective pressure? (2) the mechanical effeciency

A:

Q: describe the operation of electro-mechanical parking brake.

A: Electro-mechanical parking brake An electromechanical parking brake is a type of parking brake that…

Q: Explain the operation of an integral drum brake parking brake.

A: The integral brake is a parking brake that is on the inside of a disk brake system. Cables are used…

Q: Which of the following is not a factor in determiningthe effectiveness of a brake system?a. Heat…

A: Given Data : Effectiveness of brake system

Q: 1. Why many irregularities are there in your car tyre face? explain the concept. 2. Explain the type…

A: 1. Why many irregularities are there in your car Tyre face ?          Note :- you have posted…

Q: 6. While discussing types of coil springs: Techni- cian A says that linear-rate coil springs have…

A: Q.6) Answer" Both Technician A and B is correct. Technician A is correct because in Linear rated…

Q: Automotive technology Backing plates, struts, levers, and other metal brake parts should be Select…

A: Given: How the various automotive parts should be cleaned.

Q: 1) the brake power delivered (bp) = 104.846 Kw (2) the brake mean effective pressure (bmep) = 6.867…

A: Draw the schematic diagram of the plant

Q: Describe the common complaints caused by faulty shock absorber ons while driving.

A:

Q: Q: Check if the brake below is suitable for stopping the shaft or not? The shaft has power of 20KW…

A:

Q: Derive the relation of tarque for internal expanding shae brake?

A: The answer is in the following step

Q: Required Informatlon The figure shows an Internal rim-type brake having an Inside rim diameter of…

A: Write the given data.      r=300 mm2=150 mm   R=125 mm   b=40 mm   a=125 mm  F=1.8…

Q: Materials properties analysis of brake disc. Please discus about the mechanical properties

A: Whenever braking applied kinetic energy is converted to heat energy. The material used for the…

Q: When examining disc brakes: Technician A visually inspects the rotor and says that the rotor can be…

A: Technician A is correct.

Q: how is the braking force of drum-type brakes controlled

A: Brake: The brake is defined as a machine element which is used to retard the moving member or to…

Q: There is 465 psi in the hydraulic system that is powering a caliper with two pistons on each side of…

A: The normal force exerted by the caliper on the rotor can be determined as,

Q: What are the technical specifications of brakes?

A: The design specifications of a drum brake consist of Brake drum radius Brake shoe Lining arc radius…

Q: Explain the operation of the ABS Brake system

A: The Anti-lock Braking System (ABS) is a safety feature in modern vehicles designed to prevent the…

Q: Compare between Disk brake and drum brake based on the Pallowing factors. brake factor lucecporabion…

A:

Q: A short-shoe drum brake having f= 0.25, a = 1.0 m, b = 0.4 m, c = 50 mm, and r= 0.3 m is to absorb…

A:

Q: A band brake (Figure 1) uses a 100 mm wide woven lining having design values of f = 0.3 a pmax = 0.7…

A: Givenw=100mmf=0.3Pmax=0.7 MPaN=150 rpm

Q: File Help x, Intro Torque Moment of Inertia Angular Momentum PHET Applied Force 2Fapplied=4 N Forake…

A: Given: Fapplied = 4N Fbrake = -3N r = 4m

Q: A prony brake is to be built to measure the torque output of a 10-hp motor that operates at a speed…

A:

Q: How can you give the effect of the hydraulic brake

A: Given Data : Effect of hydraulic break

Q: Where is the highest value for the brake thermal efficiency and the lowest value for the specific…

A: Figure shows the variation of brake specific fuel consumption and brake thermal efficiency of a high…

Q: 1KN -500→-500- 310 260mm

A: To determine the torque required to apply brake

Q: Explain in detail about hydraulic ram with any one practical example

A: A hydraulic ram is a normal cyclic pump that is powered by hydropower. This is a device that raises…

Q: the aid of a diagram explain the function of the main parts of a master cylinder used in hydraulic…

A:

Q: Shown in the figure is a single block brake. The intensity of pressure between the block and brake…

A: Free body diagram of given figure

Q: When performing the air brake system leakage test, the Certified Inspector must reject the vehicle…

A: Answer = False

Q: A. Kineticenergy B. Coefficient of friction C. Bonded linings Linings attached to their backings…

A: Given questions are related to IC engines and braking systems in machine design. A. Kinetic EnergyB.…

Q: What is the difference between block brakes with short and long shoes?

A: Consider the diagram shown below for the block brakes with short and long shoes.

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.