H.W1 : An 2.44 m span cantilever beam has a rectangular section and reinforcement as shown in Figure. The beam carries a dead load , including its own weight of 2 kN.m and a live load of 1.22 kN.m. Using fy = 414 MPa and f. = 27.58 MPa , check if the beam is safe to carry the above loads. 3 # 7 2.44 m- 200 mm 460 mm 396 mm

H.W1 : An 2.44 m span cantilever beam has a rectangular section and reinforcement as shown in Figure. The beam carries a dead load , including its own weight of 2 kN.m and a live load of 1.22 kN.m. Using fy = 414 MPa and f. = 27.58 MPa , check if the beam is safe to carry the above loads. 3 # 7 2.44 m- 200 mm 460 mm 396 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. 2.0 m | P₁ = 45 KN W₁ = 44.24 kN/m 3.0 m a. b. 3-200 6-200 350mm by 400mm f'c-35 MPa fy=415 MP.. Ps= 10 mm conc. cover= 40mm 250mm by 400mm f'c-21 MPa fy=415 MPa Ps= 10 mm conc. cover= 40mm
Q3/ design a single simply supported beam with a span of 5.5 m. the superimposed dead load is 18 kN/m and the live load is 12kN/m. Assume h=L/12 and b=0.5d. use one line of o25mm diameter bars . fc=31 Mpa and fy=414 Mpa.
4. The beam shown in figure below (W 410 x 46.1) has continuous lateral support of both flanges. The uniform load is service load consisting of 50% dead load and 50% live load. The dead load includes the weight of the beam. Use A36M steel materials and Determine the service superimposed dead load and live load in (kN /m) can be applied on the member. tum. +1.85 + 5.4m 7/ -1.8mx|
Help me solve this. I will generously give a feedback and a 5 star. Thank you. A 3m-LONG CANTILEVER BEAM IS CARRYING A UNIFORM DEADLOAD OF 20 kN/m (EXCLUDING SELFWEIGHT OF THE BEAM), AND A LIVE LOAD OF 15 kN/m. OTHER GIVEN: fc = 27.5 MPa fy = 414 MPa b = 300mm h = 600mm diameter of main reinforcements, db = 25mm diameter of transverse reinforcements, ds = 12mm use clear concrete cover of 45mm unit weight of concrete is 25kN/m3 Solve for the following: a. As (area) required b. No. of 25mm reinforcements required to resist Mu c. Spacing of stirrups at the critical location (d from face of the support) - use manual calculations, show your solutions.
Situation 4: A W530 x 92 simply supported beam has a length of 12 m. The beam supports a super imposed dead load of 12 kN/m and equal concentrated load of "P" at quarter points. The compression flange is laterally supported at point loads and the reactions. Use A 36 steel Fy = 250 MPa Properties of W 530 x 92 A 11800 mm² d = 533 mm bf = 209 mm tf = 15.6 mm tw = 10.2 mm rts 54.6 mm ry = 45.0 mm kdes 28.4 mm Sx = 2080 x 10³ mm³ Zx 2360 x 10³ mm³ J= 762 x 10³ mm³ Cw=1600 x 10⁹ mm 1. What is the maximum laterally unbraced length at which the nominal moment capacity maybe taken at FyZx?) 2. What is the allowable moment? use Cb = 1.4911 3. What is the allowable load "P" so that it will not exceed its allowable stress design ( 4. What is the allowable load P so that it will not exceed the allowable shearing stress? 5. What is the allowable moment if the beam is laterally support at supports only? Use 1.4911
The rectangular beam with a span length of 7.2 m has an effective depth, d = 430mm and a width of 250mm. It has 2-legged 10mmØ stirrups spaced at 130 mm on centers all throughout the beam length. Determine the maximum wu that the beam can carry based on the shear capacity of the beam. Use fc' = 21MPa and Grade 40 rebars. a. Adopt smaller of S' : S'1 = Avfy / (0.062b√f'c) S'2 = Avfy / (0.35b) b. S" = (0.062/0.33) / S'1 c. 1. if S > S' ; ØVn = Ø 0.5Vc 2. if S"<S<S' ; Smax = least of S' or d/2 or 600mm i. S> Smax ; ØVn = Ø 0.5Vc ii. S< Smax ; ØVn = Ø (Vc + ( Avfyd / S ) ) 3. if S < S" ; Smax = least of S' or d/4 or 300mm i. S> Smax ; Vs = 0.33√f'c bwd ØVn = Ø (Vc + 0.33√f'c bwd) ii. S< Smax ; ØVn = Ø (Vc + ( Avfyd / S ) ) Find: 1. Vc 2. s' and s'' 3. smax 4. ØVn 5. Wu
A beam with S = 1,050 x 103 mm³, carries uniformly distributed load W1 and a concentrated load P1. Determine loads W and P if the flexural stress is limited to “X" MPa. SET W1, P1, kN L1, m L2=L3, m o (“X"), LN/m. MPa В 3W W 3 1 145 L1 3. L3 5. L2
4. The beam shown in figure below (W 410 x 46.1) has continuous lateral support of both flanges. The uniform load is service load consisting of 50% dead load and 50% live load. The dead load includes the weight of the beam. Use A36M steel materials and Determine the service superimposed dead load and live load in (kN/m) can be applied on the member. m. |--1.8²| 1.8mx/ 5. Design a bearing plate to distribute the reaction of the W 410 x 46.1 in problem (4). The beam is to be supported on reinforced concrete wall with f'c = 35 MPa. Use A36M steel materials for the beam and bearing plate. 5.4m
A. A simply supported girder spans 12 m. It carries two (2) beams, each at 4.5 m. from the supports. The concentrated load from each beam is 75 KN. Don't neglect the weight of beam W410x100 Properties Beam Section W410 mm x 100 kg/m Ix-397 x 106 mm, ly=49 x 106 mmª, tf = 21 mm, tw=15mm, Modulus of elasticity E = 200 GPa, Consider bending about the x-axis. A=12710 mm², d=415 mm, bf=265 mm, a. Which of the following gives the maximum bending stress? Fy=248 MPa
AW14 x 68 is used as a beam having a simple span of 6 m. Properties of WF Section. d = 356.62 mm bf = 254.89 mm tf = 18.29 mm tw = 10.54 mm Sx = 1688 x 10° mm Ry = 62.48 mm Zx = 1885 x 10 mm3 Fy = 345.6 MPa El 150 000 kN-m2 Determine the safe uniform live load it could carry so that it will not exceed the allowable live load deflection of 1/360 of the span. (kN/m)
1%9. l. In. • f 10 Y:- quiz2.pdf > Quiz: Design the reinforcement steel that necessary for the shcar and torsion for the rectangular cantilever beam shown in figure. Use for stirrups (o12) and let f.=25 MPa, f-400 MPa, dead load (5 kN/m?) and live load (10 kN/m), take into account the self-weight of beam. All dimensions in (mm) 1000 800 3000 300 Cnand TEXTEDT II
Determine the maximum safe service live load that the beam can carry if the service dead load is 10kN/m including the beam weight and based on the capacity of the beam section shown. Use fc'=40MPA and fy=415MPa. top bars are 6-36mm and bottom bars are 3-36mm, center to center distance between the top bar layers is 108mm. WLL = kN/m 70 mm 108 mm 352 mm 70 mm 300 mm 7.2m 6.7m A В O O